2022 Honda Passport Wheel Interchange

2022 Honda Passport Wheel Fitment Guide

Use the specifications below as a reference when checking wheels and tires for a 2022 Honda Passport. Fitment can vary by trim, equipment, market, and wheel package, so confirm the information on your vehicle, in the owner’s manual, or with a Honda dealer before purchasing.

Known OEM Fitment For 2022 Honda Passport

The following OEM fitment values are known for the supplied 2022 Honda Passport reference configuration. They should not be treated as a complete list of every trim or factory wheel package.

A wheel should match the 5x120 bolt pattern and provide a center bore that is compatible with the vehicle hub. A larger wheel center bore may require correctly sized hub-centric rings, while a smaller center bore generally will not fit over the hub. Confirm the wheel’s lug-seat design and required hardware before installation because the M14 x 1.5 thread specification alone does not identify the correct lug nut seat.

How To Use The Wheel Interchange Calculator

Use the calculator to compare a donor vehicle’s wheel and tire setup with the setup installed on your 2022 Honda Passport. Enter the donor specifications under “Wheels from (donor vehicle)” and enter the Passport information under “Installed on (your vehicle).”

For a direct comparison, enter the known Passport reference values above, including the 18-inch diameter, 8.0-inch width, ET55 offset, 245 mm tire section width, and 60 percent aspect ratio. If your Passport has a different factory package, use the tire sidewall and wheel markings or verify the specification through an OEM source.

You can also test a proposed custom setup by adjusting “Custom wheel size” for rim diameter, width, and offset, then adjusting “Custom tire size” for section width and aspect ratio. When rim diameter changes, the calculator updates the tire diameter in the comparison. Review the changes in overall diameter, sidewall height, wheel position, and tire width, but remember that calculator results do not replace a physical clearance inspection.

Compare the inner and outer position of the proposed wheel against the reference wheel. A change in width or offset can affect clearance to the brake caliper, strut, suspension components, fender, and inner liner. Confirm load capacity, tire speed rating, and vehicle-specific requirements separately.

Fitment Checklist Before You Buy

Before ordering wheels or tires, verify each of the following against the vehicle and the product documentation:

• Confirm the vehicle’s exact trim, drivetrain, brake package, and factory tire size.
• Match the 5x120 bolt pattern and confirm that the wheel has five mounting holes.
• Check the 64.1 mm hub diameter and determine whether hub-centric rings are needed for the selected wheel.
• Compare wheel diameter, width, and offset with the calculator and the known reference values.
• Confirm that the wheel clears the brake caliper, suspension, steering components, and wheel-well liner.
• Check the tire’s load index, speed rating, construction, and approved rim-width range.
• Maintain adequate tire clearance at full steering lock and through suspension compression.
• Verify TPMS sensor compatibility and whether the sensors require relearning after installation.
• Confirm the wheel’s lug-seat type, lug nut dimensions, and required thread engagement. Do not assume the original lug nuts fit aftermarket wheels.
• Inspect used wheels for cracks, bends, corrosion, repaired damage, and distorted mounting surfaces.

Do not rely only on a wheel being advertised for a Honda or on the bolt pattern matching. Offset, center bore, brake clearance, lug-seat design, load rating, and tire size all affect safe fitment.

Plus Sizing And Common Upgrades

Plus sizing usually means fitting a larger-diameter wheel with a lower-profile tire while keeping the overall tire diameter close to the original. The goal is to limit changes to speedometer behavior, gearing, ground clearance, and electronic systems. Use the calculator to compare the proposed diameter with the installed reference before buying.

A wider wheel or tire may improve steering response, but it can also increase the risk of contact with the strut, suspension, fender, or liner. A lower-profile tire generally provides less sidewall protection from potholes and curb impacts. Larger wheels can also increase cost and may affect ride comfort.

Do not select a tire solely by matching its diameter. Check the tire manufacturer’s approved rim-width range, load index, speed rating, clearance, and whether the size is appropriate for the vehicle. Any nonstandard setup should be checked by a qualified tire or wheel technician before driving.

Installation Tips

Clean the hub face and wheel mounting surface before installation. Rust, dirt, paint buildup, or debris between the wheel and hub can prevent the wheel from seating correctly and may cause loosening or vibration.

Install the correct lug nuts by hand first to avoid cross-threading. Tighten them in a star pattern with the vehicle supported safely, then torque them to the vehicle or wheel manufacturer’s specified value. The correct torque value was not provided here, so use the owner’s manual, Honda service information, or the wheel manufacturer’s instructions rather than guessing.

After installation, check for contact by turning the steering from lock to lock and inspecting the inner wheel, tire, brake components, and suspension. If practical, perform a careful clearance check through suspension travel. Recheck lug torque after the manufacturer’s recommended initial driving interval.

After changing wheels or tires, reset or relearn the TPMS system as required. Check tire pressure when the tires are cold and use the vehicle’s door-jamb label or owner’s manual for the correct pressure.

Tools And Helpful Supplies

Useful equipment for a careful wheel installation can include a calibrated torque wrench, properly sized socket, breaker bar, jack and jack stands or an appropriate lift, wheel chocks, a tire-pressure gauge, a tread-depth gauge, and a flashlight for clearance checks.

A torque wrench is available through Amazon automotive torque wrench search results. If the replacement wheel has a larger center bore, confirm the exact hub and wheel dimensions before purchasing Amazon 64.1 mm hub-centric ring search results. Hub rings are not a substitute for the correct bolt pattern, offset, brake clearance, or properly designed wheel hardware.

FAQs

What is the bolt pattern for the 2022 Honda Passport?
The known reference fitment is 5x120. Confirm the exact vehicle and wheel package before purchase because this page may not include every trim-specific variation.

What is the center bore for the 2022 Honda Passport?
The supplied reference value is 64.1 mm. An aftermarket wheel with a larger bore may need correctly sized hub-centric rings. A wheel with a smaller bore generally will not fit over the vehicle hub.

What tire size is listed for this 2022 Honda Passport reference?
The supplied tire measurements correspond to 245/60R18. Check the tire sidewall and the vehicle door-jamb label to confirm the size installed on your specific Passport.

What wheel size is listed for the 2022 Honda Passport?
The known reference wheel is 18 inches in diameter and 8.0 inches wide, with ET55 offset and 6.17 inches of backspacing. These values should be verified against the vehicle’s trim and factory equipment.

Can I use wheels from another vehicle with a 5x120 bolt pattern?
A matching bolt pattern is only one part of fitment. You must also compare center bore, offset, width, brake clearance, lug-seat design, load capacity, and tire clearance. Use the calculator for dimensional comparison, then complete a physical inspection.

Will changing wheel diameter change tire diameter?
Changing wheel diameter requires a corresponding tire-size change to maintain a similar overall tire diameter. The calculator updates tire diameter when you change rim diameter, but the result must still be checked against tire availability, approved rim width, load rating, and vehicle clearance.

Do I need different lug nuts for aftermarket wheels?
You may. The known thread size is M14 x 1.5, but the correct lug nut also depends on the wheel’s lug-seat style, seating depth, and required engagement. Verify the wheel manufacturer’s hardware requirements before installation.

How can I confirm the correct OEM fitment for my trim?
Check the tire and wheel markings, the driver-side door-jamb label, the owner’s manual, official Honda service information, or a Honda dealer. Compare those details with the calculator and do not purchase based on a generic vehicle listing alone.