2017 Chevrolet Malibu Wheel Interchange

2017 Chevrolet Malibu Wheel Fitment Guide | wheelinterchange.com

Known OEM Fitment For 2017 Chevrolet Malibu

The values below are verified examples from OEM data for at least one 2017 Malibu configuration. Trims and option packages can differ. If a value on your car does not match, confirm it against the driver door jamb tire label and the owner’s manual, then use the on-page calculator to compare.

Important: The wheel size shown is 17 inch while the tire example is 16 inch. This indicates multiple factory configurations. Always verify your specific trim’s wheel and tire sizes on the door label and in OEM literature, then use the calculator below to compare any changes.

How To Use The Wheel Interchange Calculator

• Set Installed on to 2017 Chevrolet Malibu so your car is the reference.
• Pick Wheels from to try a donor vehicle or enter Custom wheel size for a direct size test.
• Adjust Custom wheel size: rim diameter, rim width, and offset. Watch inner clearance and poke changes.
• Adjust Custom tire size: section width and aspect ratio. When you change rim diameter, the tire diameter in the comparison updates so you can keep overall diameter consistent.
• Keep an eye on the calculator’s outputs: change in inner clearance, outer poke, overall tire diameter difference, and estimated speedometer impact.
• Use the OEM values above as a baseline. If your door label lists 205/65R16, the overall diameter is about 26.5 in. Target a similar diameter when plus sizing to minimize ABS and speedometer effects.
• Finish with a physical test fit when possible, especially if you are close on strut, caliper, or fender clearance.

Fitment Checklist Before You Buy

• Bolt pattern: The wheel must be 5x115. Do not use 5x114.3 without proper adapters. Adapters add thickness and change offset, so evaluate carefully.
• Center bore: The Malibu hub is 70.3 mm. Wheels with larger bores require hub-centric rings sized 70.3 mm inner to your wheel’s bore outer.
• Offset and backspacing: Start from the known OEM example of ET 45 and about 5.52 in backspacing. Use the calculator to keep inner clearance to struts and outer poke within safe limits for your suspension and fenders.
• Thread and hardware: Threads are M12 x 1.5. Match lug nut seat type to the wheel design. Verify that you achieve sufficient thread engagement. A practical guideline is engagement at least equal to the stud diameter.
• Tire diameter: Aim to keep overall tire diameter close to your door label size. Many installers target within about 3 percent to limit speedometer and ABS impact. Confirm using the calculator.
• Brake and caliper clearance: Spoke shape and barrel design matter. Always confirm radial and lateral clearance over the front brakes.
• TPMS: The 2017 Malibu uses tire pressure sensors. Reuse compatible sensors or ensure new sensors are compatible and perform a relearn per the owner’s manual.
• Load and speed ratings: Meet or exceed the OEM ratings listed on your door label.

Plus Sizing And Common Upgrades

Because 2017 Malibu trims used more than one factory size, plus sizing must start with your exact door label size.

• If your label shows 205/65R16, the overall diameter is roughly 26.5 in. When moving to a larger wheel diameter, pick a tire aspect ratio and width that keep the overall diameter near that number. Enter candidates in the calculator and review the diameter difference and clearance changes.
• If your car has a 17 inch OEM wheel like 17 x 7.5 ET 45, use that as the baseline in the calculator and test wider widths or different offsets. Watch inner clearance to struts and outer poke to fenders.
• Steering feel and ride: Lower aspect ratio tires sharpen response but may ride firmer and increase impact risk. Wider tires can improve grip but may tramline and can reduce winter performance.
• Staggered setups are uncommon for this platform. A square setup simplifies rotation and ABS calibration.

Installation Tips

• Test fit each front wheel first. Spin by hand to confirm caliper and knuckle clearance.
• Clean the hub face and wheel mounting pad to bare metal. Remove rust and debris that can create runout.
• If using hub-centric rings, seat them fully on the wheel before mounting.
• Hand start all lug nuts to avoid cross threading. Tighten in a star pattern.
• Use a torque wrench and tighten to the factory torque spec from your owner’s manual or service information. Do not use impact tools for final torque.
• After 50 to 100 miles, recheck torque on all lug nuts.
• TPMS: If sensors were replaced or relocated, perform the relearn process specified by Chevrolet and verify with a scan tool if needed.

Tools And Helpful Supplies

• 1/2 inch torque wrench
• Low profile floor jack
• Jack stands
• M12 x 1.5 lug nuts Verify seat type and length for your wheels.

FAQs

• What is the bolt pattern for the 2017 Chevrolet Malibu

  5x115. Always match this exactly unless you use professional adapters, which add thickness and change offset. Evaluate adapter use very carefully.

• What is the center bore

  70.3 mm at the hub. Wheels with a larger bore can be made hub-centric with rings sized 70.3 mm inner to the wheel’s bore outer. Wheels with a smaller bore will not fit.

• What offset should I use

  A known OEM example is ET 45 on a 17 x 7.5 wheel. Other trims may differ. Use the calculator to compare any new offset to your baseline and check inner clearance and outer poke, then physically test fit.

• Can I run 5x114.3 wheels on a 5x115 Malibu

  Not recommended. The mismatch can stress studs and cause vibration. Only purpose-built adapters change the bolt pattern, but they add thickness and alter scrub radius and load. A correct 5x115 wheel is the safe choice.

• What tire size keeps my speedometer accurate

  Match the overall diameter listed on your door label. If your label shows 205/65R16, that is about 26.5 in overall. Use the calculator to choose alternate sizes that stay close to that diameter.

• What is the lug nut thread size and seat type

  Threads are M12 x 1.5. Seat type depends on the wheel design. Many aftermarket wheels use a 60 degree conical seat, but you must confirm the seat required by your specific wheel.

• Do I need to reprogram TPMS when changing wheels

  If you move the existing sensors to new wheels, a relearn may be required. If you install new sensors, make sure they are compatible with the 2017 Malibu and perform the relearn as described by Chevrolet.