2018 Acura NSX
Direct Fit- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
- Wheel geometryCompatible with OEM envelope
Mounting dimensions align with known OEM fitment for this vehicle.
2019 Acura NSX Wheel Interchange
OEM wheel and tire fitment specs for the 2019 Acura NSX, including bolt pattern (PCD), center bore diameter, thread size, rim diameter, rim width, wheel offset, and backspacing.
2019 Acura NSX Fitment Specs
Baseline mounting dimensions used for interchange decisions.
Bolt Pattern5x120
Center Bore70.1 mm
Lug ThreadM14 x 1.5
OEM Wheel Sizes19"
OEM Widths8.5"
OEM Offset Range55 mm
Wheels That Interchange With a 2019 Acura NSX
Results are evaluated from bolt pattern, center bore direction, OEM width/offset envelope, and lug hardware – not bolt pattern alone.
Direct Fit
2020 Acura NSX
Direct Fit- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
- Wheel geometryCompatible with OEM envelope
Mounting dimensions align with known OEM fitment for this vehicle.
2017 Acura NSX
Direct Fit- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
- Wheel geometryCompatible with OEM envelope
Mounting dimensions align with known OEM fitment for this vehicle.
2021 Acura NSX
Direct Fit- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
- Wheel geometryCompatible with OEM envelope
Mounting dimensions align with known OEM fitment for this vehicle.
2022 Acura NSX
Direct Fit- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
- Wheel geometryCompatible with OEM envelope
Mounting dimensions align with known OEM fitment for this vehicle.
Check Fitment
2010 Acura ZDX
Check Fitment- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
Donor width/offset sits outside the known OEM envelope for this vehicle.
2011 Acura ZDX
Check Fitment- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
Donor width/offset sits outside the known OEM envelope for this vehicle.
2012 Acura ZDX
Check Fitment- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
Donor width/offset sits outside the known OEM envelope for this vehicle.
2013 Acura ZDX
Check Fitment- Bolt pattern5x120 · Match
- Center bore70.1 mm · Match
Donor width/offset sits outside the known OEM envelope for this vehicle.
Acura NSX Years With Compatible Wheels
Only years with evidence-based interchange relationships are listed. Adjacent years are not assumed compatible.
Will Wheels From Another Vehicle Fit?
Compare a donor vehicle or custom wheel against this 2019 Acura NSX.
Compare
Compare wheel compatibility between two vehicles
Wheels from (donor vehicle)
Installed on (your vehicle)
Selected Car:
2019 Acura NSX
Compare Rims
Specification
Wheels from
Installed on
Result (Click it)
Bolt Pattern
The total number of bolt holes and the diameter of the circle they form.
-
5x120
Center Bore
The hole in the center of the wheel that fits over the vehicle’s hub.
-
70.1 mm
Thread Size
The size and spacing of the threads on the bolts or nuts that hold the wheel in place.
-
M14 x 1.5
Rim Diameter
The wheel diameter in inches that determines which tire sizes will fit.
-
19"
Rim Width
The distance between the inner edges of the wheel is measured in inches.
-
8.5"
Wheel Offset
How far the wheel sits inward or outward relative to the hub mounting surface.
-
55 mm
Backspacing
Shows how much space the wheel takes up toward the inside of the vehicle.
-
-
Wheel Fasteners
The type of hardware used to secure the wheel to the vehicle.
-
-
Wheel Fitment Parts for the 2019 Acura NSX
Products below are matched to required fitment dimensions from our parts inventory. Confirm seat style, thickness, and clearance before ordering.
Lug Nuts / Wheel Bolts
M14 x 1.5
Dorman 611-236 Wheel Lug Nut M14-1.50
M14 x 1.5 · Confirm wheel seat style before ordering
View on Amazon →
White Knight M14 x 1.50 Lug Nuts
M14 x 1.5 · Confirm wheel seat style before ordering
View on Amazon →
White Knight 3809XLBK-33AM Black M14x1.50 Lug Nuts
M14 x 1.5 · Confirm wheel seat style before ordering
View on Amazon →Wheel Adapters
5x120 · 70.1 mm hub
Directional bolt-pattern adapters. A spacer does not change PCD.
Ezaccessory Wheel Adapters 5x120 to 5x127
5x120 → 5x127
View on Amazon →
EZAccessory Wheel Adapters 5x120 to 5x4.5
5x120 → 5x114.3
View on Amazon →
Autobahn88 Wheel Adapters (0.8")
5x120 → 5x114.3
View on Amazon →As an Amazon Associate we earn from qualifying purchases. Product availability and pricing may change.
Why These Wheels Fit
Wheel interchange depends on more than bolt pattern. Where data is available, this site compares:
- Bolt pattern / PCD
- Center bore direction (donor wheel bore must not be smaller than the hub)
- Wheel diameter, width, and offset against known OEM ranges
- Lug thread / hardware differences (vehicle-side hardware)
A normal wheel spacer does not change bolt pattern. Hub rings cannot enlarge a wheel bore that is smaller than the hub. Brake clearance and tire package fitment still require vehicle-specific checks when not confirmed in the dataset.
2019 Acura NSX wheel fitment guide
You’re looking for fast, safe answers on the 2019 Acura NSX. Below is the OEM baseline we have, how to use the on-page calculator to compare options, and the critical checks before you buy or bolt up.
Spec snapshot
| Bolt pattern | 5x120 |
| Center bore | 70.1 mm |
| Thread size | M14 x 1.5 |
| Rim diameter | 19 in |
| Rim width | 8.5 in |
| Offset (ET) | 55 mm |
| Backspacing | 6.42 in |
| Tire size | 245/35R19 |
Note: The NSX commonly runs a staggered setup. The data above may reflect only one axle. If your trim differs, confirm each axle’s factory spec in the owner’s manual, door placard, or OEM parts catalog, and validate with the calculator on wheelinterchange.com.
tl;dr
- Baseline: 5x120, 70.1 mm bore, M14x1.5, 19x8.5 ET55, 245/35R19.
- Treat this as the reference when comparing donor wheels in the calculator.
- Match bolt pattern and center bore. Keep inner and outer clearances safe.
- Staggered is likely. Verify front vs rear before ordering.
- Torque fasteners to OEM spec and re-check after 50–100 miles.
Recommendation
Work from the OEM geometry first. Use the calculator to compare any donor wheel or custom size against 19x8.5 ET55 with a 245/35R19 tire. Keep overall tire diameter close to stock, and watch inner clearance to suspension and brakes as you change width or offset.
- If a donor wheel shares 5x120 and clears the 70.1 mm hub, you’re halfway there. If the wheel’s center bore is larger, plan hub-centric rings to 70.1 mm. If it’s smaller, it will not fit without machining.
- Offset changes: a smaller ET pushes the wheel outward, a larger ET moves it inward. Use the calculator to see inner and outer clearance changes in millimeters.
- Tire changes: adjusting rim diameter updates overall tire diameter in the tool. Aim for a small variance so ABS, traction control, and speedometer behavior stay predictable.
- Seat type and nuts: match the lug seat to the wheel design and use M14x1.5 hardware. Do not mix ball and cone seats.
Impact
- Handling: wider wheels can add grip but may tramline. Offset shifts can alter steering feel and scrub radius.
- Clearance: inner barrel vs calipers and knuckle is the first constraint. Outer lip vs fender is the second. The calculator highlights both.
- Speedometer: diameter changes adjust indicated speed. The tool shows the percentage difference for quick judgment.
- Tire wear: mismatched diameters front to rear can stress AWD systems. Keep axle-to-axle diameter relationships consistent with OEM.
- Ride and NVH: larger diameters with shorter sidewalls ride firmer and transmit more noise.
Risks and gotchas
- Partial data: the NSX often uses different front and rear sizes. Confirm both axles with OEM sources if you plan a full set.
- Centering: driving on lug-centric fit can cause vibration. Use hub-centric rings if the wheel bore is larger than 70.1 mm.
- Brake clearance: spoke design matters as much as barrel diameter. Test for caliper-to-spoke clearance, not just inner barrel.
- Lug engagement: ensure full thread engagement with M14x1.5 hardware, especially if using spacers. Avoid thin shank or mismatched seat nuts.
- Load rating: wheel and tire load ratings must meet or exceed OEM. Do not assume aftermarket ratings are sufficient.
- TPMS: plan compatible sensors and relearn procedure for 2019 Acura systems.
Next actions
Checklist
- Identify if your 2019 NSX has staggered OEM sizes. Check door placard and manual.
- Open the wheelinterchange.com calculator. Set “Installed on” to 2019 Acura NSX. Enter the baseline above.
- Enter the donor wheel or your custom size. Adjust width and offset to visualize inner and outer clearance changes.
- Set tire size. Verify overall diameter and speed error presented by the tool. Keep differences small and balanced front to rear.
- Confirm bolt pattern 5x120, center bore 70.1 mm, and M14x1.5 hardware compatibility.
- Plan hub-centric rings if the wheel bore is larger than 70.1 mm.
- Before final mounting, test-fit one corner. Spin-check for caliper and suspension clearance with the car on stands.
- Install with correct seat-type lugs. Torque to OEM spec. Re-torque after 50–100 miles.
Helpful tools
- 1/2 inch drive torque wrench
- M14x1.5 lug nuts (match seat to your wheels)
- 70.1 mm hub-centric rings to suit your wheel bore
You now have the baseline and a process. Use the calculator to validate geometry, then confirm hardware and clearances. That keeps your 2019 Acura NSX safe and dialed-in.
