2019 BMW M5 Wheel Interchange

2019 BMW M5 Wheel Fitment Guide - Wheel Interchange

Known OEM Fitment For 2019 BMW M5

The values below reflect confirmed factory specifications for the 2019 BMW M5 where available. Some vehicles were delivered with different wheel packages. If yours differs, use your door-jamb tire sticker, owner’s manual, and the on-page calculator to confirm your exact setup before buying parts.

From the listed 275/40R19 tire, the approximate overall diameter is 702.6 mm (about 27.66 in). Keeping new tire diameter within about plus or minus 3 percent of this helps maintain speedometer accuracy and proper ABS/DSC behavior.

How To Use The Wheel Interchange Calculator

The calculator compares two setups: Wheels from (donor vehicle) versus Installed on (your vehicle). It also lets you try a Custom wheel size and Custom tire size. Follow these steps:

1) Set Installed on to 2019 BMW M5, then verify or enter your exact OEM rim and tire sizes from your tire sticker. If your factory size differs from the table above, use your exact values.

2) If you are evaluating wheels from another vehicle, select that donor vehicle. The tool will instantly show bolt pattern, center bore, and key differences.

3) To test aftermarket options, open Custom wheel size and enter a rim diameter, width, and offset. The calculator will display inner clearance changes to the strut and outer poke toward the fender compared to your OEM baseline.

4) Open Custom tire size and enter a section width and aspect ratio. When you change rim diameter, the tool updates tire diameter for an apples-to-apples comparison.

5) Review the results. Pay close attention to inner clearance (strut, spring perch, brake lines), outer clearance (fender lip, liners), and overall tire diameter change for speedometer and gearing effects.

6) If you plan to use spacers or different seat-style hardware, reflect those changes in the calculator and notes, then confirm with physical test fitment before driving.

Fitment Checklist Before You Buy

Use this quick checklist to minimize surprises:

• Match bolt pattern: 5x112.
• Confirm center bore: 66.6 mm hub. If the wheel’s center bore is larger, you will need hub-centric rings sized to 66.6 mm. If smaller, the wheel will not fit the hub.
• Verify fasteners: Thread size is M14 x 1.25. Seat style and length must match the wheel design and any spacers. BMW applications typically use wheel bolts rather than nuts.
• Offset and width: Start from OEM ET 26 mm and 9.5 in width, then use the calculator to see inner and outer clearance changes. Even small offset shifts can affect fender and strut clearance.
• Brake caliper and barrel clearance: The M5 uses large brakes. Do a physical test fit and check spoke and barrel clearance. Do not assume another BMW wheel will clear.
• Tire diameter and load rating: Keep close to the OEM 275/40R19 overall diameter and always meet or exceed the OEM load index and speed rating.
• TPMS compatibility: Plan to reuse or program compatible sensors. New sensors may be required with additional sets of wheels.
• Spacers, if used: Only hub-centric spacers with matching 66.6 mm lip and bore. Use properly extended wheel bolts sized for the spacer thickness.
• Alignment and fender checks: After installation, check for rubbing at full lock, full compression, and during reversing. A fresh alignment is recommended.
• Seasonal and chain clearance: If you run winter tires or chains, verify clearance with the chosen size before road use.

Plus Sizing And Common Upgrades

Many owners explore wider tires or larger diameter wheels. Because trims and brake packages vary, exact upgrade sizes are not listed here. Instead, use the OEM baseline above and these guidelines:

1) Keep overall tire diameter near 702.6 mm (about 27.66 in). Staying within about plus or minus 3 percent helps maintain instrument accuracy and stability system calibration.

2) Width vs offset: Increasing wheel width typically requires offset adjustments. The calculator will show inner clearance loss and outer poke. Aim to maintain safe inner clearance to struts and at least a few millimeters of fender clearance under full bump and steering.

3) Brake clearance: Larger diameter wheels can improve caliper clearance, but spoke shape and barrel design still matter. Always test fit.

4) Staggered setups: If you choose a staggered arrangement, confirm front and rear rolling diameters remain compatible for AWD or stability systems, and rotate tires accordingly if patterns allow.

Installation Tips

Prepare the workspace, chock wheels, and lift the car using proper jack points. Support with stands on a level surface. Clean the hub face so the wheel seats flush and free of rust or debris. If the wheel’s center bore is larger than 66.6 mm, install correct hub-centric rings before mounting.

Hand start all M14 x 1.25 bolts to avoid cross-threading. Snug in a crisscross pattern, then torque in stages to the BMW factory specification for your vehicle, found in the owner’s manual or service information. Recheck torque after 50 to 100 miles. If spacers are installed, use proper extended hardware and repeat the torque procedure.

After installing new tire sizes, set cold pressures to the values recommended for your load and speed on the door-jamb label or BMW guidance, then use the vehicle menu to reset TPMS and steering angle or related adaptations as required.

Tools And Helpful Supplies

These common tools make wheel work safer and easier. Match any tool or hardware to your exact vehicle and wheel setup.

• 1/2 inch drive torque wrench
• Wheel hanger guide pin M14
• Jack stands
• BMW TPMS service kit

FAQs

What is the 2019 BMW M5 bolt pattern?
5x112.

What center bore do I need?
66.6 mm. If your wheel’s bore is larger, use hub-centric rings sized to 66.6 mm. A smaller bore will not fit.

What wheel fasteners does it use?
M14 x 1.25 wheel bolts. Confirm seat style and length with your specific wheels and any spacers.

How close should my new tire diameter be?
Target near the OEM diameter of about 702.6 mm (27.66 in). A deviation of about plus or minus 3 percent is a common guideline to keep systems happy, but always verify with the calculator and your tire professional.

Will smaller diameter wheels fit over the brakes?
Brake clearance varies by wheel model and spoke design. The M5 has large calipers, so always test fit or obtain a brake clearance template from the wheel maker before purchasing.

Can I use spacers safely?
Yes if you use quality hub-centric spacers that match 66.6 mm and install the correct extended wheel bolts. Re-torque and inspect regularly. Spacers change effective offset, so simulate this in the calculator first.

What is the OEM offset and width I should use as a baseline?
ET 26 mm and 9.5 in width based on the known data above. If your factory setup differs, input your exact values from your vehicle sticker and manual into the calculator to create the correct baseline.

How do I confirm which factory sizes my specific car has?
Use the door-jamb tire label and your owner’s manual. You can also check OEM parts information for your VIN. Enter those values into the calculator for the most accurate comparison.