2019 Chevrolet Cruze Wheel Interchange

2019 Chevrolet Cruze Wheel Fitment And Interchange Guide

Known OEM Fitment For 2019 Chevrolet Cruze

The 2019 Chevrolet Cruze was sold with multiple wheel and tire packages that vary by trim and option package. Only the values below are confirmed. If a specification is not listed, it may vary by trim. Use the on-page calculator and verify with OEM sources like the owner’s manual or a GM parts catalog before you buy.

Important note: The confirmed data shows both an 18x7.5 ET42 wheel and a 195/65R15 tire, which come from different factory packages. Do not assume these are paired together. If your trim differs, confirm your exact factory sizes on your door jamb label, owner’s manual, or a GM parts database, and then compare in the calculator.

How To Use The Wheel Interchange Calculator

• Set Installed on to 2019 Chevrolet Cruze. This is your vehicle.
• If you are comparing wheels from another vehicle, enter that under Wheels from. If you are testing an aftermarket setup, use Custom wheel size and Custom tire size.
• Enter rim diameter, rim width, and offset. The tool shows changes to inner clearance, outer poke, track width, and backspacing.
• Enter tire section width and aspect ratio. When you change rim diameter, the calculator updates overall tire diameter in the comparison so you can keep speedometer error in check.
• Aim to keep overall tire diameter close to stock, typically within about plus or minus 3 percent, and ensure inner clearance to the strut and brakes remains safe.
• Use the output to check fender clearance and scrub radius changes before purchasing.

Fitment Checklist Before You Buy

• Bolt pattern must be 5x105. Adapters change geometry and are not recommended for street use unless engineered and installed carefully.
• Center bore should seat on 56.6 mm. If the wheel bore is larger, plan on hub-centric rings to avoid vibration.
• Thread size is M12 x 1.5. Verify lug nut type and seat style match the wheel design.
• Offset and backspacing must clear suspension and fenders. Use the calculator to compare against known OEM examples like 18x7.5 ET42 with about 5.4 in backspacing.
• Brake caliper clearance. Physically test fit or use a template from the wheel maker.
• Load rating. Wheel and tire load index must meet or exceed the Cruze’s GAWR and GVWR requirements.
• TPMS. Plan to transfer or replace sensors and perform a relearn after installation.
• Stud engagement. Ensure at least 6.5 to 8 full turns of a standard M12 x 1.5 lug nut. Do not use spacers unless proper stud length and hubcentric location are maintained.
• Speedometer and ABS. Keep overall tire diameter close to stock to minimize electronics and gearing impact.
• OEM verification. Cross-check your door jamb label, owner’s manual, or a GM parts catalog for your exact factory sizes.

Plus Sizing And Common Upgrades

The Cruze was offered with multiple factory wheel diameters. If you want to plus-size, use the calculator to maintain similar overall tire diameter and inner clearance to the strut and spring perch.

• Maintain overall diameter close to stock. This keeps your speedometer and gearing behavior predictable.
• Watch offset. Lower ET pushes the wheel outward which can contact the fender on compression. Higher ET moves inward and can contact suspension. Compare changes in the calculator from a known OEM baseline such as 18x7.5 ET42.
• Match tire width to wheel width. Check the tire manufacturer’s approved rim width range for the exact tire you choose.
• Brake upgrades. If you plan larger brakes, confirm spoke and barrel clearance with the wheel manufacturer’s templates.

Because factory sizes varied in 2019, do not assume a specific plus-size is correct for your trim. Always verify with the calculator and OEM references before purchasing.

Installation Tips

• Test fit each wheel on the front and rear before mounting tires. Spin the hub by hand to check for caliper and knuckle clearance.
• Clean the hub face and the wheel mounting pad until bare metal for proper clamping. Remove rust and debris.
• If using hub-centric rings, seat them fully on the hub and ensure they match 56.6 mm inner diameter.
• Use the correct lug seat style for your wheel. Hand start all lugs and snug in a star pattern.
• Torque lug nuts to the specification in the owner’s manual using a calibrated torque wrench. Do not lubricate lug threads unless the manufacturer specifically instructs it.
• Re-torque after 50 to 100 miles of driving.
• Perform TPMS relearn per GM procedure after installation.
• After installation, turn steering lock-to-lock and compress the suspension over a driveway ramp to confirm clearance.

Tools And Helpful Supplies

• 1/2 inch drive torque wrench
• Thin wall lug nut socket set
• Hub-centric rings 56.6 mm ID for wheels with a larger center bore
• GM TPMS relearn tool

FAQs

• What is the bolt pattern on the 2019 Chevrolet Cruze?

  5x105.

• What is the center bore for the 2019 Cruze?

  56.6 mm.

• What lug thread does the Cruze use?

  M12 x 1.5. Confirm your lug seat style matches the wheel you are installing.

• What is the OEM wheel offset?

  One confirmed OEM example is ET 42 mm on an 18x7.5 wheel. Other trims may differ. Use the calculator and verify against your exact factory size before changing offset.

• What tire size came on the 2019 Cruze?

  One confirmed OEM tire size is 195/65R15. Other factory tire sizes existed. Check your door jamb label or owner’s manual for your trim.

• Can I install wheels with a different bolt pattern like 5x110 or 5x114.3?

  No. The hub is 5x105. Using adapters changes geometry and can introduce safety issues. Use wheels with the correct 5x105 pattern.

• Do I need hub-centric rings?

  If your aftermarket wheel has a center bore larger than 56.6 mm, use rings to center the wheel on the hub and reduce vibration.

• Will 18 inch wheels fit my Cruze?

  Some 2019 Cruze configurations used 18x7.5 ET42. Fitment depends on your trim, brakes, and tire size. Compare with the calculator and verify brake and fender clearance on your vehicle.

• What torque should I use on the lug nuts?

  Always follow the torque spec in the Chevrolet owner’s manual or GM service information for your exact trim. Do not guess. Re-torque after 50 to 100 miles.

• Will my TPMS work with new wheels?

  Yes if you transfer your sensors or install compatible replacements and complete a GM TPMS relearn. Sensor frequency and protocol must match your vehicle.