2017 Chevrolet Equinox Wheel Interchange

2017 Chevrolet Equinox Wheel Fitment Guide | wheelinterchange.com

Known OEM Fitment For 2017 Chevrolet Equinox

The specifications below reflect an OEM 2017 Chevrolet Equinox configuration we have on record. Trims and option packages may use different wheel and tire sizes. If anything on your vehicle does not match, confirm against your door-jamb tire label, the owner’s manual, or OEM parts data, then use the on-page calculator to compare.

Notes:

• Other factory sizes may exist on some 2017 Equinox trims. Always verify the exact size shown on your vehicle’s tire label and compare in the calculator.
• If your current wheels differ from the values above, treat the above as a reference and model your actual setup in the calculator before buying.

How To Use The Wheel Interchange Calculator

• Set Installed on to 2017 Chevrolet Equinox to lock in your vehicle’s baseline specifications.
• Pick Wheels from to match a donor setup you want to test. This can be another vehicle or a custom setup.
• Use Custom wheel size to change rim diameter, width, and offset. The calculator will show positional changes relative to your Equinox.
• Use Custom tire size to change section width and aspect ratio. When you change rim diameter, the calculator updates tire diameter in the comparison so you can maintain overall diameter as needed.
• Review the comparison for changes in inner clearance and outer position, and check tire diameter difference to avoid rubbing and speedometer error.
• Iterate until the results indicate clearances and overall diameter are within your targets, then verify physically with a test fit whenever possible.

Fitment Checklist Before You Buy

• Bolt pattern must be 5x120.
• Center bore on the vehicle hub is 66.9 mm. Aftermarket wheels with a larger bore require hub-centric rings sized to 66.9 mm at the hub side.
• Thread size is M14 x 1.5. Use hardware that matches both thread and the wheel’s seat type. Verify lug nut or bolt seat with the wheel manufacturer.
• Target an offset close to the OEM 43 mm unless you have measured clearance for changes. Use the calculator to see how different offsets shift the wheel inboard and outboard.
• Backspacing reference is about 5.19 in on the 17x7 wheel. Use this as a cross-check when evaluating alternatives.
• Brake and suspension clearance. Confirm spoke-to-caliper and inner barrel-to-strut clearance. A minimum few millimeters static clearance is commonly targeted, but verify on-vehicle.
• Tire load index and speed rating must meet or exceed OEM specifications for the 2017 Equinox trim. Check your door-jamb label.
• TPMS compatibility. Plan to transfer sensors or install compatible new sensors and perform relearn as required.
• Do a test fit on the hub before mounting tires when possible to confirm bore fit, stud engagement, and caliper clearance.

Plus Sizing And Common Upgrades

Starting from the known OEM setup above, many owners explore Plus 1 or Plus 2 packages. Fitment varies by wheel design, exact offset, tire model, and trim equipment. Follow these guidelines:

• Keep overall tire diameter close to stock to maintain speedometer accuracy and help avoid rubbing. A common target is within about 2 to 3 percent of OEM. Use the calculator’s tire comparison to check this.
• As wheel width increases, adjust offset in the calculator to keep inner clearance and outer poke in safe ranges for your vehicle.
• Confirm brake and suspension clearance with the exact wheel design. Spoke shape can affect caliper clearance even if size math looks fine.
• If using wheels with a larger center bore than 66.9 mm, add hub-centric rings so the wheel centers on the hub.
• Do not assume an upgrade that fits another Equinox trim will fit yours without checking. Verify against your door-jamb label and model it in the calculator.

Installation Tips

• Safely raise and support the vehicle on quality jack stands placed at approved lift points. Chock the opposite wheels.
• Clean the hub face and wheel mounting pad. Remove rust and debris so the wheel sits flush.
• Dry-fit each wheel on the hub before mounting tires when trying a new style. Check bore fit and caliper clearance.
• If using hub-centric rings, seat them fully against the hub and ensure they match 66.9 mm on the hub side.
• Install lug hardware by hand first to prevent cross-threading. Do not lubricate studs or nuts unless the manufacturer explicitly instructs it.
• Tighten lugs in a crisscross pattern in steps to the factory torque specification from your owner’s manual or OEM service information.
• Re-torque after 50 to 100 miles of driving.
• Perform a TPMS relearn if you moved or replaced sensors, following GM procedures for the 2017 Equinox.

Tools And Helpful Supplies

• Floor jack and jack stands
• Breaker bar and the correct-size lug socket for your lugs
• 1/2 inch drive torque wrench
• M14x1.5 lug nuts matched to your wheel seat type
• Hub-centric rings 66.9 mm hub side for aftermarket wheels with larger bores
• TPMS service kit or sensors compatible with your 2017 Equinox
• Wire brush and mild anti-seize for the hub face only if recommended by OEM

FAQs

What is the bolt pattern for the 2017 Chevrolet Equinox?
It is 5x120.

What is the center bore size?
The vehicle hub is 66.9 mm. Aftermarket wheels with a larger bore will need hub-centric rings sized to 66.9 mm on the hub side.

What is the thread size for the lug hardware?
M14 x 1.5. Use hardware that matches both this thread and the wheel’s seat type.

Will wheels from another Chevrolet fit my 2017 Equinox?
Only if the bolt pattern is 5x120, the center bore is 66.9 mm or larger with rings, the offset and width clear your brakes and fenders, and the tire load rating is adequate. Use the calculator to compare and always test fit.

What offset should I choose?
The known OEM offset is 43 mm on a 17x7 wheel. If you change wheel width or design, use the calculator to visualize inner and outer position changes. Verify clearance on the vehicle before driving.

What tire sizes can I use when plus sizing?
Use the calculator to keep overall diameter close to stock and confirm clearance. Stay within your vehicle’s load and speed ratings as shown on the door-jamb label. Tire sizes vary by wheel width and offset, so verify before purchase.

Do I need new TPMS sensors?
You can transfer your existing sensors if compatible with the new wheels. If you install new sensors, ensure they are compatible with the 2017 Equinox and perform the relearn procedure.

What is the wheel lug torque spec?
Torque specifications vary by wheel and hardware and are provided by GM for the 2017 Equinox. Refer to your owner’s manual or OEM service information and torque in a crisscross pattern.

Are spacers safe to use?
Use only high-quality hub-centric spacers that match 5x120 and 66.9 mm hub size, with proper extended hardware, and only when necessary to correct clearance. Model the change in the calculator and test fit carefully.