2004 Chrysler Crossfire Wheel Interchange

OEM wheel and tire fitment specs for the 2004 Chrysler Crossfire, including bolt pattern (PCD), center bore diameter, thread size, rim diameter, rim width, wheel offset, and backspacing.

Recorded OEM specifications for the 2004 Chrysler Crossfire, donor years with overlapping ranges, and a calculator to compare a selected wheel. Range overlap is not a guaranteed fit.

Start a donor comparison

Save these wheel specs to your Ownery garage

2004 Chrysler Crossfire Fitment Specs

Baseline mounting dimensions used for interchange decisions.

Bolt Pattern5x112
Center Bore66.5 mm
Lug ThreadM12 x 1.5 View M12 x 1.5 options on Amazon
OEM Wheel Sizes18" – 19"
OEM Widths7.5" – 8.5"
OEM Offset Range30 mm – 35 mm

Multiple OEM configurations exist for this vehicle. Fitment can vary by trim, brakes, and factory wheel package – confirm your exact setup before buying.

Center-bore records disagree: year-level hub 66.6 mm vs trim range 66.5–66.5 mm. Interchange below does not treat this as an unqualified match.

Thread-only product links are shopping examples, not verified fits. Seat style is not confirmed here. As an Amazon Associate we earn from qualifying purchases.

Explore wheels at Tire Rack

Selected size: 18 × 7.5″ · ET +35

Showing matching bolt patterns and offsets up to 30 mm lower. Confirm center bore, load rating, and clearance at Tire Rack.

We may earn a commission when you buy through these links. Prices and availability may change.

Donor vehicles with overlapping OEM specs

These are vehicle-year records whose recorded OEM ranges overlap this 2004 Chrysler Crossfire. Overlap is not a guarantee that a specific wheel will install. Selected-wheel comparison is in the calculator below.

Evaluated 4 donor years. Listed 4 eligible overlaps (not all evaluated years are compatible). Showing all listed.

2005–2007 Chrysler Crossfire

Check wheel configurationCenter-bore records disagree

Years grouped because recorded compatibility evidence is equivalent. Each year keeps its own page.

  • 2005
  • 2006
  • 2007
  • Bolt pattern5x112 · Same recorded PCD
  • Center bore66.5 mm · same recorded hub figure
  • Wheel geometryOEM width/offset ranges overlap (not a specific wheel)

Center-bore records disagree (target year-level hub 66.6 mm vs trim range 66.5–66.5 mm; donor year-level hub 66.6 mm vs trim range 66.5–66.5 mm). Unqualified overlap is not claimed until the conflict is resolved.

2008 Chrysler Crossfire

Insufficient dataCenter-bore records disagree
  • Bolt pattern5x112 · Same recorded PCD
  • Center bore66.6 mm donor vs hub 66.5 mm
  • Wheel geometryNot fully recorded

Dataset suggestionHub-centric rings ≈ 66.6 → 66.5 mm – not a verified installation requirement.

Wheel width/offset data is incomplete. Hub ring 66.6 → 66.5 mm may apply if mounting dimensions are otherwise compatible.

Chrysler Crossfire Years With Compatible Wheels

Only years with evidence-based interchange relationships are listed. Adjacent years are not assumed compatible.

Will Wheels From Another Vehicle Fit?

Compare a donor vehicle or custom wheel against this 2004 Chrysler Crossfire. Use Compare in calculator on a donor row above to fill the donor side of this same calculator.

Compare

Compare wheel compatibility between two vehicles

Wheels from (donor vehicle)

Installed on (your vehicle)

Selected Car:

2004 Chrysler Crossfire

Compare Rims

Specification
Wheels from
Installed on
Result (Click it)
Bolt Pattern
Bolt Pattern
The total number of bolt holes and the diameter of the circle they form.
-
5x112
Center Bore
Center Bore
The hole in the center of the wheel that fits over the vehicle’s hub.
-
66.5 mm
Thread Size
Thread Size
The size and spacing of the threads on the bolts or nuts that hold the wheel in place.
-
M12 x 1.5
Rim Diameter
Rim Diameter
The wheel diameter in inches that determines which tire sizes will fit.
-
18"
Rim Width
Rim Width
The distance between the inner edges of the wheel is measured in inches.
-
7.5"
Wheel Offset
Wheel Offset
How far the wheel sits inward or outward relative to the hub mounting surface.
-
35 mm
Backspacing
Backspacing
Shows how much space the wheel takes up toward the inside of the vehicle.
-
-
Wheel Fasteners
Wheel Fasteners
The type of hardware used to secure the wheel to the vehicle.
-
-

Wheel Fitment Parts for the 2004 Chrysler Crossfire

Example products matched to recorded thread, hub, or spacer dimensions. They are not verified fits. Confirm seat style, thickness, and clearance before ordering.

Lug Nuts / Wheel Bolts

M12 x 1.5

As an Amazon Associate we earn from qualifying purchases. Product availability and pricing may change.

2004 Chrysler Crossfire Wheel Fitment Guide

Known OEM Fitment For 2004 Chrysler Crossfire

The values below reflect information provided for at least one factory configuration of the 2004 Chrysler Crossfire. Other trims or axles may differ. If your vehicle appears to have a staggered setup or different sizes front to rear, verify each axle against your tire placard and the on-page calculator.

Bolt pattern 5x112
Center bore 66.6 mm
Thread size M12 x 1.5
OEM rim diameter 18 in
OEM rim width 8.0 in
OEM wheel offset ET 35 mm
Backspacing 5.38 in
OEM tire size 225/40R18

Values not shown may vary by trim or axle. Confirm any missing specifications using the tire placard on your driver door jamb, your owner’s manual, and the on-page calculator.

How To Use The Wheel Interchange Calculator

The calculator compares Wheels from a donor vehicle against what will be Installed on your vehicle. You can also enter a Custom wheel size and Custom tire size to test any aftermarket setup.

  • Set Installed on to 2004 Chrysler Crossfire. Enter your known baseline, for example 18x8.0 ET35 with 225/40R18 if that matches your axle.
  • For a proposed setup, either pick a donor vehicle or switch to Custom wheel size. Adjust rim diameter, rim width, and offset. If you change rim diameter, the tire comparison will update as you adjust tire section width and aspect ratio.
  • Watch inner clearance to the strut and brake components, and outer position relative to the fender. Ensure there is sufficient space through full steering lock and suspension travel.
  • Aim to keep overall tire diameter close to your OEM baseline so speedometer and ABS behavior remain consistent. Many owners target within about 2 to 3 percent, but always verify against OEM guidance.
  • If your Crossfire is staggered, run the calculator separately for front and rear axles using each axle’s baseline sizes from your tire placard.

Fitment Checklist Before You Buy

  • Bolt pattern - The wheel must be 5x112.
  • Center bore - The hub is 66.6 mm. If a new wheel has a larger bore, use hub-centric rings with 66.6 mm inner diameter. Do not use a wheel with a smaller bore.
  • Offset and backspacing - Compare your target wheel to the OEM baseline in the calculator. Confirm inner clearance to struts, spring perches, and brake calipers, and outer clearance to fenders and liners.
  • Brake caliper clearance - Visually check spoke design and barrel clearance. Some designs with the same size and offset may still contact calipers.
  • Tire diameter - Keep overall tire diameter close to OEM to protect ABS, traction control, and speedometer accuracy.
  • Load rating - Wheel and tire load ratings must meet or exceed OEM requirements.
  • Lug seat type - Confirm whether your Crossfire uses ball seat or cone seat fasteners and match the wheel accordingly. Inspect your current hardware or consult OEM documentation.
  • Fastener type and thread - Thread is M12 x 1.5. Verify whether your vehicle uses lug bolts or studs with nuts and purchase hardware to match the wheel’s seat type.
  • TPMS and valve stems - If your car is equipped with TPMS, plan sensor transfer or new compatible sensors.

Plus Sizing And Common Upgrades

The OEM example above is 18x8.0 ET35 with 225/40R18. Many owners explore wider wheels or larger diameters, but fitment depends on offset, tire profile, brake clearance, and suspension height. The following are examples to test in the calculator, not confirmed fitments:

  • Same diameter, wider wheel - Example to try: 18x8.5 with a matched offset change to maintain inner and outer clearance. Test 225/40R18 or 235/40R18 and verify fender and strut clearance.
  • Plus-1 diameter - Example to try: 19x8.5 with 235/35R19. Check inner clearance and outer poke. Confirm overall diameter remains close to OEM.
  • Staggered setups - If your vehicle uses different front and rear sizes, evaluate each axle independently in the calculator and cross-check with your tire placard.

Always validate with the calculator, measure your clearances, and confirm against OEM sources before purchasing.

Installation Tips

  • Test fit every wheel without a tire first to confirm hub fit, caliper clearance, and stud or bolt engagement.
  • Clean the hub face and center bore with a wire brush. Lightly clean the wheel mounting pad. A thin film of anti-seize on the hub face only may help prevent corrosion where permitted by OEM guidance. Do not lubricate lug threads unless specified by the manufacturer.
  • If your wheel bore is larger than 66.6 mm, install correct hub-centric rings before mounting.
  • Hand start all fasteners. If your car uses lug bolts, a wheel hanger guide pin can help align the wheel.
  • Tighten in a star pattern and torque to the factory specification for the 2004 Chrysler Crossfire. Refer to your owner’s manual or service information.
  • Re-torque after 50 to 100 miles of driving.
  • After any significant size or offset change, schedule an alignment and check for rubbing at full lock and over bumps.

Tools And Helpful Supplies

  • Floor jack and quality jack stands
  • 1/2 inch drive torque wrench - Search on Amazon
  • Breaker bar and 17 mm or 19 mm socket as applicable
  • Digital caliper for measuring hub bore, stud or bolt protrusion, and spacer thickness - Search on Amazon
  • Wheel hanger guide pin M12 x 1.5 if using lug bolts - Search on Amazon
  • Hub-centric rings with 66.6 mm inner diameter if needed - Search on Amazon
  • Nylon brush, brake cleaner, and shop rags
  • Tire pressure gauge

FAQs

  • What is the bolt pattern for the 2004 Chrysler Crossfire?

    5x112.

  • What center bore does the Crossfire use?

    66.6 mm. Use hub-centric rings if your aftermarket wheels have a larger center bore. Do not use a wheel with a smaller bore.

  • What is the thread size for wheel fasteners?

    M12 x 1.5. Verify whether your vehicle uses lug bolts or studs with nuts and ensure the seat type matches the wheel.

  • What are the OEM wheel and tire sizes?

    An example OEM setup provided is 18x8.0 ET35 with 225/40R18 and 5.38 in backspacing. Other trims or axles may differ. Check your tire placard and use the calculator for each axle if staggered.

  • How much can I change offset or width without rubbing?

    This varies with tire choice, ride height, and brake package. Use the calculator to compare inner and outer positions to the OEM baseline and physically measure clearances on your car.

  • Can I run 19 inch wheels?

    Possibly, depending on width, offset, and tire size. Test options like 235/35R19 in the calculator and verify caliper, strut, and fender clearance. Confirm overall diameter is close to OEM and check with OEM sources before purchase.

  • Do I need new lug hardware?

    You may, if the new wheel uses a different seat type or requires a different shank length. Match M12 x 1.5 thread and the correct seat style specified for the wheel. Torque to the OEM spec for the 2004 Crossfire.

Always verify final fitment with the on-page calculator at wheelinterchange.com and OEM service information before buying.

Methodology and sources

Wheel interchange depends on more than bolt pattern. Where data is available, this site compares recorded OEM values:

  • Bolt pattern / PCD
  • Center bore direction (donor wheel bore must not be smaller than the hub)
  • Wheel diameter, width, and offset against known OEM ranges
  • Lug thread / hardware differences (vehicle-side hardware)

A normal wheel spacer does not change bolt pattern. Hub rings cannot enlarge a wheel bore that is smaller than the hub. Brake clearance and tire package fitment still require vehicle-specific checks when not confirmed in the dataset.

Nick Marchenko

Automotive Expert