2006 Chrysler Sebring Wheel Interchange

OEM wheel and tire fitment specs for the 2006 Chrysler Sebring, including bolt pattern (PCD), center bore diameter, thread size, rim diameter, rim width, wheel offset, and backspacing.

Recorded OEM specifications for the 2006 Chrysler Sebring, donor years with overlapping ranges, and a calculator to compare a selected wheel. Range overlap is not a guaranteed fit.

Start a donor comparison

Save these wheel specs to your Ownery garage

2006 Chrysler Sebring Fitment Specs

Baseline mounting dimensions used for interchange decisions.

Bolt Pattern5x100, 5x114.3
Center Bore57.1 mm
Lug ThreadM12 x 1.5 View M12 x 1.5 options on Amazon
OEM Wheel Sizes15" – 18"
OEM Widths6" – 8"
OEM Offset Range38 mm – 46 mm

Multiple OEM configurations exist for this vehicle. Fitment can vary by trim, brakes, and factory wheel package – confirm your exact setup before buying.

Thread-only product links are shopping examples, not verified fits. Seat style is not confirmed here. As an Amazon Associate we earn from qualifying purchases.

Explore wheels at Tire Rack

Selected size: 15 × 6″ · ET +42

Showing matching bolt patterns and offsets up to 30 mm lower. Confirm center bore, load rating, and clearance at Tire Rack.

We may earn a commission when you buy through these links. Prices and availability may change.

Donor vehicles with overlapping OEM specs

These are vehicle-year records whose recorded OEM ranges overlap this 2006 Chrysler Sebring. Overlap is not a guarantee that a specific wheel will install. Selected-wheel comparison is in the calculator below.

Evaluated 23 donor years. Listed 23 eligible overlaps (not all evaluated years are compatible). Showing all listed.

1999–2005 Chrysler Sebring

Check wheel configurationWheel bore may need hub-centric rings; clearance unverified

Years grouped because recorded compatibility evidence is equivalent. Each year keeps its own page.

  • 1999
  • 2000
  • 2001
  • 2002
  • 2003
  • 2004
  • 2005
  • Bolt pattern5x100 · Same recorded PCD
  • Center bore67.1 mm donor vs hub 57.1 mm
  • Wheel geometryOEM width/offset ranges overlap (not a specific wheel)

Dataset suggestionHub-centric rings ≈ 67.1 → 57.1 mm – not a verified installation requirement.

See matching hub rings

Hub-centric rings of about 67.1 → 57.1 mm mm may be relevant if the wheel bore is larger than the hub; they cannot enlarge a smaller bore.

2007–2010 Chrysler Sebring

Check wheel configurationWheel bore may need hub-centric rings; clearance unverified

Years grouped because recorded compatibility evidence is equivalent. Each year keeps its own page.

  • 2007
  • 2008
  • 2009
  • 2010
  • Bolt pattern5x114.3 · 5x114.3
  • Center bore67.1 mm donor vs hub 57.1 mm
  • Wheel geometryOEM width/offset ranges overlap (not a specific wheel)

Dataset suggestionHub-centric rings ≈ 67.1 → 57.1 mm – not a verified installation requirement.

See matching hub rings

Hub-centric rings of about 67.1 → 57.1 mm mm may be relevant if the wheel bore is larger than the hub; they cannot enlarge a smaller bore.

1999–2000 Chrysler Cirrus

OEM specs overlapOEM ranges overlap – confirm the specific wheel

Years grouped because recorded compatibility evidence is equivalent. Each year keeps its own page.

  • 1999
  • 2000
  • Bolt pattern5x100 · Same recorded PCD
  • Center bore57.1 mm · same recorded hub figure
  • Wheel geometryOEM width/offset ranges overlap (not a specific wheel)

Recorded OEM bolt pattern, center bore, and width/offset ranges overlap. This is not a guarantee that every wheel from the donor year fits this vehicle.

2001–2010 Chrysler PT Cruiser

OEM specs overlapOEM ranges overlap – confirm the specific wheel

Years grouped because recorded compatibility evidence is equivalent. Each year keeps its own page.

  • 2001
  • 2002
  • 2003
  • 2004
  • 2005
  • 2006
  • 2007
  • 2008
  • 2009
  • 2010
  • Bolt pattern5x100 · Same recorded PCD
  • Center bore57.1 mm · same recorded hub figure
  • Wheel geometryOEM width/offset ranges overlap (not a specific wheel)

Recorded OEM bolt pattern, center bore, and width/offset ranges overlap. This is not a guarantee that every wheel from the donor year fits this vehicle.

Chrysler Sebring Years With Compatible Wheels

Only years with evidence-based interchange relationships are listed. Adjacent years are not assumed compatible.

Will Wheels From Another Vehicle Fit?

Compare a donor vehicle or custom wheel against this 2006 Chrysler Sebring. Use Compare in calculator on a donor row above to fill the donor side of this same calculator.

Compare

Compare wheel compatibility between two vehicles

Wheels from (donor vehicle)

Installed on (your vehicle)

Selected Car:

2006 Chrysler Sebring

Compare Rims

Specification
Wheels from
Installed on
Result (Click it)
Bolt Pattern
Bolt Pattern
The total number of bolt holes and the diameter of the circle they form.
-
5x100
Center Bore
Center Bore
The hole in the center of the wheel that fits over the vehicle’s hub.
-
57.1 mm
Thread Size
Thread Size
The size and spacing of the threads on the bolts or nuts that hold the wheel in place.
-
M12 x 1.5
Rim Diameter
Rim Diameter
The wheel diameter in inches that determines which tire sizes will fit.
-
15"
Rim Width
Rim Width
The distance between the inner edges of the wheel is measured in inches.
-
6.0"
Wheel Offset
Wheel Offset
How far the wheel sits inward or outward relative to the hub mounting surface.
-
42 mm
Backspacing
Backspacing
Shows how much space the wheel takes up toward the inside of the vehicle.
-
-
Wheel Fasteners
Wheel Fasteners
The type of hardware used to secure the wheel to the vehicle.
-
-

Wheel Fitment Parts for the 2006 Chrysler Sebring

Example products matched to recorded thread, hub, or spacer dimensions. They are not verified fits. Confirm seat style, thickness, and clearance before ordering.

Lug Nuts / Wheel Bolts

M12 x 1.5

As an Amazon Associate we earn from qualifying purchases. Product availability and pricing may change.

2006 Chrysler Sebring Wheel Fitment Guide | wheelinterchange.com

Known OEM Fitment For 2006 Chrysler Sebring

The following specs reflect one OEM configuration for the 2006 Chrysler Sebring. Other trims or packages may differ. If your vehicle’s door-jamb tire placard shows different values, use those and confirm with the on-page calculator and OEM sources.

Bolt pattern (studs x PCD)5x100
Center bore57.1 mm
Thread sizeM12 x 1.5
OEM rim diameter15 in
OEM rim width6.0 in
OEM wheel offsetET 42 mm
OEM backspacing4.65 in
OEM tire size205/65R15

Interchange basics. A donor wheel must have 5x100 bolt pattern, a center bore of 57.1 mm or larger (use hub-centric rings if larger), and dimensions that clear your brakes, suspension, and fenders. Use the calculator to compare width and offset changes before buying. If your trim differs, verify against your owner’s manual, the door-jamb placard, and OEM parts catalogs.

How To Use The Wheel Interchange Calculator

  • Open the calculator and set “Installed on (your vehicle)” to 2006 Chrysler Sebring.
  • Pick a “Wheels from (donor vehicle)” or enter the donor wheel’s size to compare.
  • Adjust “Custom wheel size” to test different rim diameter, width, and offset. The tool shows inner clearance and outer poke changes.
  • Adjust “Custom tire size” by section width and aspect ratio. When you change rim diameter, the calculator updates tire diameter in the comparison so you can keep overall diameter close to stock.
  • Check the differences for:
    • Inner clearance to strut, spring perch, and knuckle.
    • Outer poke toward the fender and bumper liner.
    • Overall tire diameter change that may affect speedometer, ABS, and gearing.
  • If your trim’s OEM size differs from the table above, enter your placard size first, then compare options against that baseline.

Fitment Checklist Before You Buy

  • Bolt pattern: Must be 5x100. Wheels with 5x114.3 or 5x110 will not fit your studs.
  • Center bore: 57.1 mm hub. If the wheel’s bore is larger, use hub-centric rings sized to 57.1 mm. If smaller, the wheel will not seat.
  • Thread and hardware: M12 x 1.5 studs. Match lug nut thread and seat type to the wheel. Do not mix ball-seat and conical-seat hardware.
  • Offset and width: Use the calculator to confirm inner and outer clearances with your brake package and suspension. Measure on the car if needed.
  • Brake clearance: Test-fit to ensure spoke and barrel clear the front caliper and rear drum or caliper.
  • Load rating: Wheel and tire load index must meet or exceed the OEM requirement on your tire placard.
  • Tire diameter: Keep overall diameter close to stock to reduce the risk of rubbing and speedometer error. Verify with the calculator.
  • Spacers/adapters: Only if necessary. They must be hub-centric to 57.1 mm and require sufficient stud engagement. Re-check laws and safety.

Plus Sizing And Common Upgrades

Owners often explore larger diameters or wider wheels. Availability and clearance can vary by trim and brake package on the 2006 Sebring, so treat the sizes below as possibilities to test rather than guarantees.

  • Plus-one or plus-two sizing: Use the calculator to pair a larger rim with a lower-profile tire so overall diameter stays close to stock.
  • Wider tires: Compare section width changes to confirm fender and strut clearance at full lock and full compression.
  • Offset tuning: Small offset changes can help inner or outer clearance. Always verify with the calculator and a physical test-fit.

If your Sebring trim shows different OEM specs than listed above, start from your placard size and re-run all comparisons in the calculator.

Installation Tips

  • Test-fit every wheel on the hub without a tire first if possible. Confirm hub bore seating, caliper clearance, and stud engagement.
  • Clean the hub face and center pilot. Remove rust so the wheel seats flush and torque is accurate.
  • If using hub-centric rings, install them snugly on the wheel and ensure they sit fully on the 57.1 mm hub.
  • Hand-thread lugs, snug in a star pattern, then torque in stages to the OEM spec from your owner’s manual. Re-torque after 50 to 100 miles.
  • Check lock-to-lock steering and hit bumps at low speed to confirm no rubbing on liners or fenders.
  • Verify tire load index and inflation to the placard values after installation.

Tools And Helpful Supplies

FAQs

  • Will wheels from another car fit my 2006 Sebring?

    They can if key dimensions match. You need a 5x100 bolt pattern, 57.1 mm center bore or larger with rings, correct hardware, and offset/width that clear brakes, suspension, and fenders. Use the calculator to compare the donor wheel to your Sebring before buying.

  • What is the stock wheel and tire size?

    One OEM setup is 15x6 ET42 with 205/65R15 tires. Some trims may differ. Check your door-jamb tire placard and verify with OEM sources, then use that size as your baseline in the calculator.

  • Do I need hub-centric rings?

    If your wheel’s center bore is larger than 57.1 mm, use rings that step the wheel down to 57.1 mm so it centers on the hub. If the bore is smaller than 57.1 mm, the wheel will not fit.

  • What lug nuts does the Sebring use?

    The thread size is M12 x 1.5. Seat type depends on the wheel design. Match the seat type to the wheel manufacturer’s spec and do not mix ball-seat with conical-seat hardware.

  • Can I switch to a larger rim like 16 or 17 inches?

    Possibly, depending on your trim and brake package. Use the calculator to pair a suitable tire so overall diameter stays close to stock, and confirm clearance through a test-fit.

  • What offset should I use with aftermarket wheels?

    The listed OEM offset is 42 mm for the configuration above. Aftermarket offsets vary. Compare inner clearance and outer poke with the calculator and verify on the car. Do not rely on offset alone without measuring.

  • What torque should I tighten the lug nuts to?

    Use the torque specification in your owner’s manual or OEM service information for your exact trim, and torque in a star pattern. Re-check after initial driving.

Use the Wheel Interchange Calculator on wheelinterchange.com to verify all dimensions for your exact 2006 Chrysler Sebring trim before purchasing or installing wheels or tires.

Methodology and sources

Wheel interchange depends on more than bolt pattern. Where data is available, this site compares recorded OEM values:

  • Bolt pattern / PCD
  • Center bore direction (donor wheel bore must not be smaller than the hub)
  • Wheel diameter, width, and offset against known OEM ranges
  • Lug thread / hardware differences (vehicle-side hardware)

A normal wheel spacer does not change bolt pattern. Hub rings cannot enlarge a wheel bore that is smaller than the hub. Brake clearance and tire package fitment still require vehicle-specific checks when not confirmed in the dataset.

Nick Marchenko

Automotive Expert