2017 Chevrolet Colorado Wheel Interchange

2017 Chevrolet Colorado Wheel Fitment Guide

Known OEM Fitment For 2017 Chevrolet Colorado

These values reflect information available for the 2017 Chevrolet Colorado. Wheel and tire specs can vary by trim, package, engine, and brake size. If your build differs, use the on-page calculator and confirm against your owner’s manual, driver-door placard, and GM service information.

Because both a 17 inch wheel and a 16 inch tire are listed above, your Colorado may have been offered with multiple OEM wheel-tire packages. Always confirm your exact build before purchasing.

How To Use The Wheel Interchange Calculator

• Set Installed on to 2017 Chevrolet Colorado. This is your vehicle.
• Set Wheels from to the donor vehicle you want to compare. If unknown, start with the Known OEM Fitment above as the baseline.
• Use Custom wheel size to try candidate rim diameter, width, and offset. The calculator will show inner clearance to the suspension and outer poke relative to fender.
• Use Custom tire size to enter section width and aspect ratio. When you change rim diameter, the calculator will update the resulting tire diameter so you can see overall height changes.
• Watch the comparison metrics. Aim to keep overall tire diameter close to stock to protect speedometer accuracy and gearing. Keep inner clearance safe for control arms, knuckles, and liners.
• When results look promising, verify physically: measure brake caliper clearance, turn lock to lock, and check compression clearance.

Fitment Checklist Before You Buy

• Bolt pattern: Must be 6x120. Spacers or adapters change geometry and add risk. If used, they must be hub-centric and properly engineered.
• Center bore: Wheel must be 66.9 mm or larger. If larger, use hub-centric rings to 66.9 mm to prevent vibration.
• Lug hardware: Threads M14 x 1.5. Match lug seat style to the wheel. Do not mix conical, mag, or ball seats.
• Brake clearance: Confirm spoke and barrel clearance over calipers. Do not assume smaller diameter always clears. Test-fit.
• Offset and width: Start from +33 mm on 8.0 in as baseline. Large changes affect scrub radius, bearing load, and fender clearance. Use the calculator to quantify inner and outer changes.
• Tire diameter: Keep overall diameter near stock for ABS and speedometer accuracy. Use the calculator to verify.
• Load rating: Wheel and tire load index must meet or exceed the vehicle’s GAWR and GVWR requirements.
• TPMS: Plan to transfer sensors or install compatible units. Perform relearn per GM procedure after installation.

Plus Sizing And Common Upgrades

Plus sizing changes wheel diameter and width to achieve a desired look or performance while keeping overall tire diameter close to stock. Use these guidelines, then validate every change in the calculator.

• Keep overall tire diameter close to your OEM setup to maintain speedometer accuracy. The calculator will show percentage change.
• When increasing wheel width, small offset reductions are often needed to maintain inner clearance. Compare inner clearance change in the calculator to ensure suspension and liner clearance.
• Large negative offset increases outer poke and fender strike risk. Aim to keep outer position reasonable for your fenders and any mud flaps.
• All-terrain tires often run wider than the same labeled size in highway tread. Check manufacturer section width and required rim width range.
• If you change wheel diameter, confirm brake caliper to barrel clearance and tire load index. Do not assume any diameter is universally safe across trims.

Because the 2017 Colorado was sold with multiple OEM wheel-tire packages, do not assume another owner’s setup will fit your truck. Use the on-page calculator with your current setup as the Installed on baseline, then test-fit.

Installation Tips

• Test-fit each wheel on the front and rear before mounting tires. Verify hub engagement and caliper clearance.
• Clean hubs with a wire brush and remove rust ridges. A clean 66.9 mm hub face ensures proper seating.
• If using hub-centric rings, fully seat them on the wheel before mounting. Rings should be snug with no play.
• Hand start all lugs to prevent cross-threading. Tighten in a star pattern and torque to the OEM spec from your owner’s manual or service data.
• Re-torque after the first short drive and again after a heat cycle. Recheck after tire rotations.
• If using spacers, use only hub-centric units with appropriate stud engagement. Re-torque spacer nuts and then wheel nuts separately.

Tools And Helpful Supplies

• 1/2 inch drive torque wrench
• M14x1.5 lug nuts or locking lugs
• Hub-centric rings 66.9 mm
• Wheel hub wire brush

FAQs

• What is the bolt pattern on the 2017 Chevrolet Colorado?

  6x120. This means 6 wheel studs on a 120 mm circle.

• What center bore do I need for aftermarket wheels?

  The hub size is 66.9 mm. Wheels can be equal to this to be hub-centric. If the wheel bore is larger, use 66.9 mm hub-centric rings.

• Which lug nuts does it use?

  Thread size is M14 x 1.5. Match the lug seat type to your wheel. Do not reuse OEM acorn lugs on a wheel that requires mag or ball seats.

• Why do I see both 17 inch wheels and 16 inch tires listed?

  The 2017 Colorado was offered in multiple configurations. At least one build uses a 17x8 wheel and another uses a 265/70R16 tire size. Verify your exact setup on the driver-door placard or in the owner’s manual, then use the calculator to compare changes.

• How far can I deviate from the +33 mm offset?

  For easiest fitment, keep changes small and verify with the calculator. Large offset changes can reduce inner clearance or push the tire past the fender. Always measure and test-fit.

• Will my TPMS work with new wheels?

  You can typically transfer the sensors or install compatible replacements. Perform the GM relearn procedure after installation. Follow OEM instructions for your trim.

• Can I use spacers to make another wheel fit?

  Spacers introduce additional variables. If used, they must be quality hub-centric units with proper stud engagement and correct torque. Re-check torque periodically. Use the calculator to understand how spacer thickness alters effective offset.

• How do I keep the speedometer accurate when changing tire size?

  Use the calculator to keep overall tire diameter as close as possible to your OEM setup. If the change is significant, consider a calibration solution where applicable.

Always validate fitment on your specific 2017 Chevrolet Colorado using the on-page calculator, your owner’s manual, and official GM service information. If any value on this page does not match your truck, rely on your verified measurements.