2021 Chrysler Voyager Wheel Interchange

2021 Chrysler Voyager Wheel Specs, Bolt Pattern, And Interchange Guidance

Known OEM Fitment For 2021 Chrysler Voyager

The values below reflect data reported for this model year. Chrysler offered multiple wheel and tire packages, so your exact equipment may differ by trim or option package. Always confirm on your vehicle’s door placard and the wheel’s back side, then verify with the on-page calculator and OEM documentation.

Note: Both an 18x7.5 ET51 wheel and a 235/65R17 tire are listed for this model year, which indicates multiple OEM packages. Some vehicles may have 17 inch wheel and tire packages while others may have 18 inch wheel packages. Check your door placard for the exact tire size originally fitted to your Voyager.

How To Use The Wheel Interchange Calculator

• Open the calculator and set Installed on (your vehicle) to 2021 Chrysler Voyager.
• Choose Wheels from (donor vehicle) you want to compare against. This helps evaluate interchange possibilities.
• Use Custom wheel size to try different rim diameter, width, and offset values. The tool compares geometry relative to your Voyager.
• Use Custom tire size to try alternate section width and aspect ratio. When you change rim diameter, the calculator updates overall tire diameter in the comparison.
• Review inner clearance near the strut and brake components and outer position relative to the fender. Verify that overall tire diameter stays within a small change from stock to avoid speedometer and ABS issues.
• Print or save the results and physically test fit when possible before mounting tires.

Fitment Checklist Before You Buy

• Bolt pattern 5x127 - the wheel must match exactly.
• Center bore 71.5 mm - wheel bore must be 71.5 mm or larger. If larger, use hub-centric rings sized to 71.5 mm hub.
• Thread size M12 x 1.5 - use matching lug nuts or bolts with the correct seat type. Do not mix seat styles.
• Offset and width - compare with the OEM ET 51 mm, 7.5 in width using the calculator to ensure inner and outer clearances are acceptable.
• Brake and hub clearance - verify spoke and barrel clearance over calipers and that the wheel seats fully on the hub face.
• Tire overall diameter - keep close to your OEM tire diameter from the door placard to protect ride height, gearing, and speedometer accuracy.
• Load and speed rating - tires must meet or exceed the OEM placard ratings.
• TPMS - plan to transfer sensors or install compatible ones and perform relearn as required.
• Test fit - spin the wheel by hand, check lock-to-lock steering and full suspension compression for rub.

Plus Sizing And Common Upgrades

Plus sizing changes rim diameter and tire profile while keeping overall tire diameter close to stock. Because the 2021 Voyager was offered with different OEM packages, use your door placard as the baseline and verify changes with the calculator.

• Overall diameter guideline - aim to stay within a small percentage change from your stock diameter to minimize speedometer and ABS impact.
• Width and offset - wider wheels or lower offsets move the tire outward. Confirm inner strut and brake clearance and fender clearance in the calculator, then test fit.
• Example concept only - if your placard shows 235/65R17, a typical plus-one approach would pair an 18 inch rim with a lower-profile tire to keep diameter similar. This is not a recommendation for your trim. Use the calculator to select exact sizes and verify clearances.
• Ride and load - lower profiles can ride firmer. Always maintain or exceed the OEM load index.

Installation Tips

• Clean the hub face and wheel mounting pad so the wheel seats flush. Remove rust with a wire brush.
• Confirm the wheel’s center bore fits the 71.5 mm hub. If the wheel bore is larger, install proper hub-centric rings.
• Move TPMS sensors to the new wheels or install compatible sensors, then complete the relearn for your Voyager as required by the OEM procedure.
• Hand-start all M12 x 1.5 lug nuts and tighten in a star pattern. Do not use an impact to start threads.
• Torque to the OEM specification from your owner’s manual using a calibrated torque wrench. Re-check torque after a short break-in period.
• After installation, turn the steering from lock to lock and road test over bumps while listening for rubbing.

Tools And Helpful Supplies

• 1/2 inch drive torque wrench - https://www.amazon.com/s?k=torque+wrench+1%2F2+inch+drive&tag=auto-spec-20
• M12 x 1.5 lug nuts or bolts matching your seat type - https://www.amazon.com/s?k=M12x1.5+lug+nuts&tag=auto-spec-20
• TPMS service or replacement kit - https://www.amazon.com/s?k=TPMS+service+kit&tag=auto-spec-20
• Hub-centric rings 71.5 mm to your wheel bore - https://www.amazon.com/s?k=hub+centric+rings+71.5&tag=auto-spec-20

FAQs

• What is the bolt pattern for the 2021 Chrysler Voyager?

  5x127.

• What center bore do I need?

  71.5 mm hub bore on the vehicle. Wheels must be 71.5 mm or larger. Use hub-centric rings if the wheel bore is larger.

• What is the lug thread size?

  M12 x 1.5.

• What is the OEM wheel size and offset?

  An 18x7.5 wheel with ET 51 mm is listed for this model year. Because trims vary, verify your exact equipment by VIN or door placard and compare in the calculator.

• What is the OEM tire size?

  235/65R17 is listed. Some trims may differ. Always confirm on the driver door placard.

• Can I use wheels from another 5x127 vehicle?

  Possibly, but you must also match or manage center bore, offset, width, brake clearance, and lug seat style. Use the calculator and test fit before mounting tires.

• Do I need hub-centric rings?

  If your new wheel’s center bore is larger than 71.5 mm, use rings sized 71.5 mm to the wheel’s bore. If the wheel is exactly 71.5 mm, no rings are needed. A wheel with a smaller bore will not fit.

• What lug nut torque should I use?

  The exact torque is not provided here. Use the value in your owner’s manual or OEM service information for the 2021 Voyager.

• Will changing rim diameter affect my tire size?

  Yes. When you change rim diameter in the calculator, the tool updates overall tire diameter in the comparison so you can select a matching tire profile.

• Do I need new TPMS sensors?

  You can transfer your existing sensors if compatible, or install new compatible sensors. A relearn or programming step may be required depending on equipment.