1997 Dodge Neon Wheel Interchange

1997 Dodge Neon Wheel Fitment Guide

Known OEM Fitment For 1997 Dodge Neon

The values below reflect the information currently available for the 1997 Dodge Neon. If an item is marked Unknown or may vary by trim, confirm it with the on-page calculator, your owner manual, the door jamb tire placard, or an OEM parts source or dealer using your VIN.

Approximate overall tire diameter for 185/65R14 is about 23.5 in. This is a reference starting point only. Verify your exact factory size on the door placard and with the calculator.

• Bolt pattern - Count your vehicle’s wheel studs and measure PCD, or ask a dealer with your VIN. Do not assume across trims or years.
• Thread size - Verify diameter, pitch, and seat type before buying lug nuts. Use a thread pitch gauge or consult OEM sources.
• Center bore - 57.1 mm hub. Aftermarket wheels with a larger bore will require hub centering rings with 57.1 mm inner diameter.

How To Use The Wheel Interchange Calculator

The calculator compares Wheels from a donor vehicle against what will be Installed on your vehicle. It also lets you try a Custom wheel size and Custom tire size. When you change rim diameter, the calculator updates overall tire diameter in the comparison so you can see speedometer and clearance effects.

• Baseline your car - Set Installed on to 1997 Dodge Neon with the OEM tire size shown on your door placard.
• Test a donor setup - Choose a donor vehicle or enter a Custom wheel size with the rim diameter, width, and offset you want to try.
• Adjust tires - Enter a Custom tire size to keep overall diameter close to stock. Watch the calculator’s diameter and speedometer change readouts.
• Check clearances - Review inner clearance to struts and brake components, and outer poke relative to fender edges. The calculator shows how offset and width changes move the wheel in or out.
• Iterate safely - Small changes first. If you increase width, offset may need to change to maintain inner clearance. Confirm with a physical test fit before purchasing.

Always confirm final choices with OEM documentation or a dealer. The calculator is a planning tool and not a guarantee of compatibility.

Fitment Checklist Before You Buy

• Confirm bolt pattern - Count studs and measure PCD, or have a dealer verify by VIN. Unknown in the data above.
• Confirm thread size and lug seat type - Determine the correct nut or bolt thread diameter and pitch, and the seat style required by your wheels.
• Verify center bore - Vehicle hub is 57.1 mm. Use hub centering rings if your wheel bore is larger.
• Match load rating - Wheel and tire load ratings must meet or exceed OEM requirements.
• Offset and width - Start from OEM 5.5 in width and ET 40 mm. Use the calculator to model changes in inner clearance and outer poke.
• Brake and suspension clearance - Ensure spoke and barrel clear calipers, and inner rim clears struts and spring perches. Spin by hand during a test fit.
• Fender clearance - Check at full steering lock and over bumps with passengers or cargo.
• Tire diameter - Keep overall tire diameter close to stock to minimize speedometer error. Use the calculator to compare.
• Stud engagement - If using different nuts, spacers, or thicker wheel pads, ensure safe thread engagement. Follow OEM guidance.
• TPMS and accessories - If applicable, plan for valve type, sensors, and compatibility. Verify for your exact trim and market.

Plus Sizing And Common Upgrades

Plus sizing means increasing wheel diameter and using a lower-profile tire to keep overall diameter similar to stock. For example, a +1 change moves from a 14 in wheel to a 15 in wheel while selecting a tire size that maintains overall diameter near the OEM baseline.

• Use the calculator to try +1 or +2 scenarios. Keep the overall tire diameter close to stock to help maintain speedometer accuracy and gearing feel.
• Watch inner clearance. Wider wheels and tires can contact struts or liners if offset is not adjusted appropriately.
• Check brake clearance. Larger diameter wheels may clear calipers more easily, but spoke design and barrel shape still matter.
• Ride and handling - Lower profile tires can sharpen steering but may ride firmer and increase road noise. Choose quality tires and match your needs.

Because some specifications for this vehicle are unknown or may vary by trim, do not assume any upgraded size will fit. Confirm with the calculator, then verify with measurements and OEM sources before buying.

Installation Tips

• Dry fit first - Mount one wheel without a tire to check caliper, hub, and suspension clearance. Then test with the tire and rotate by hand.
• Clean mounting faces - Remove rust and debris from the hub and wheel to ensure the wheel sits flush.
• Hub centering - If using aftermarket wheels with a larger bore, install hub centering rings sized to 57.1 mm inner diameter.
• Lug hardware - Use the correct thread size and seat type for both your vehicle and wheel. Do not mix seat styles.
• Torque properly - Tighten in a crisscross pattern to the OEM torque spec from the service manual. Re-torque after 50 to 100 miles.
• Avoid lubricants on threads unless specified by OEM. If anti seize is used on the hub face, apply sparingly away from studs.
• Spacers - Only if necessary. Use hubcentric spacers and ensure proper thread engagement. Recheck torque frequently.

Tools And Helpful Supplies

• Torque wrench 1/2 inch drive
• Thin wall lug nut socket set
• Breaker bar 1/2 inch
• Hub centering rings 57.1 mm ID

FAQs

• What is the bolt pattern for the 1997 Dodge Neon?

  Unknown based on available data. Count the number of studs and measure PCD, use a bolt pattern gauge, or have a dealer confirm by VIN. You can also compare candidate wheels in the calculator, then verify physically.

• What is the center bore on this car?

  57.1 mm. If your aftermarket wheel has a larger bore, use hub centering rings with a 57.1 mm inner diameter to match the hub.

• What is the factory wheel size and offset?

  Factory wheel size listed here is 14x5.5 with approximately ET 40 mm and backspacing 4.32 in. Verify your trim’s specs on the door placard and with OEM sources.

• What tire size came stock?

  185/65R14 is shown here. Always confirm the tire label on your door jamb for your exact trim and market.

• Will 15 inch wheels fit my 1997 Neon?

  Possibly, but do not assume. Use the calculator to model a +1 setup that keeps overall diameter close to stock, then verify brake and suspension clearances with a physical test fit.

• What thread size lug nuts does it use?

  Unknown here. Measure diameter and pitch with a thread gauge, or ask a dealer by VIN. Confirm the lug seat type matches your wheels.

• How much can I change offset safely?

  There is no one-size-fits-all answer. Start near the OEM ET 40 mm and use the calculator to see inner and outer movement as you adjust width and offset. Verify clearances on the car before driving.

• Will changing tire size affect my speedometer?

  Yes if overall diameter changes. The calculator displays the difference so you can choose a size that keeps the error minimal.

• Do I need different lug nuts for aftermarket wheels?

  Often yes. Aftermarket wheels may require a specific seat type or length. Confirm thread size and seat style, and use quality hardware.

Use the wheelinterchange.com calculator to plan safely, then confirm all final selections with OEM documentation and a physical test fit before purchase.