2017 Audi SQ5 Wheel Interchange

2017 Audi SQ5 Wheel Fitment And Interchange Guide | wheelinterchange.com

Known OEM Fitment For 2017 Audi SQ5

The values below reflect known factory specifications for this vehicle. Trims or option packages may use different wheel and tire sizes. If something is not listed here or differs on your vehicle, confirm using the on-page calculator, your owner manual, the driver door jamb label, or an official Audi parts catalog.

Note: Other factory wheel and tire options may exist. Do not assume interchangeability without checking the calculator and OEM references.

How To Use The Wheel Interchange Calculator

The calculator compares Wheels from (donor vehicle) vs Installed on (your vehicle). It also lets you try a Custom wheel size and Custom tire size. When you change rim diameter, the tool updates tire diameter in the comparison.

• Set Installed on to 2017 Audi SQ5.
• For a direct OEM baseline, enter 20x8.5 ET33 with 255/45R20 in the Custom wheel and Custom tire fields.
• To test wheels from another vehicle, select that donor in Wheels from and compare clearances and tire diameter to your SQ5.
• Adjust rim width and offset to see inner clearance to suspension and outer poke vs fender. The calculator shows how far the wheel moves in or out.
• Adjust tire section width and aspect ratio to keep overall diameter close to stock for speedometer and ABS tuning. Many installers try to keep overall diameter change small, typically within a few percent.
• If using spacers, add spacer thickness to reduce the effective offset before comparing.
• Center bore must be 66.6 mm on the wheel or larger with hub-centric rings. Smaller than 66.6 mm will not seat.
• Bolt pattern must match 5x112. Thread size must match M14 x 1.5 fasteners.

Fitment Checklist Before You Buy

• Bolt pattern 5x112 must match exactly.
• Center bore: wheel must be 66.6 mm or larger. Use hub-centric rings if larger. Never use a smaller bore.
• Offset: start from OEM ET33. Use the calculator to see inner clearance to struts and outer clearance to fenders. Large offset changes can cause rubbing or bearing load issues.
• Rim width: OEM is 8.5 inches. Wider or narrower wheels change where the tire sits. Verify both inner and outer clearance with the calculator.
• Tire diameter: keep overall diameter close to stock to protect the speedometer and AWD system. The calculator shows diameter and speed difference.
• Load index and speed rating: choose tires that meet or exceed the factory ratings shown on your door placard.
• Brake clearance: visually check spoke and barrel clearance over calipers and rotors during a test fit.
• Lug seat type and fasteners: confirm the wheel’s seat type matches your fasteners and that M14 x 1.5 thread engagement is correct. Use extended fasteners if spacers are installed.
• TPMS: confirm sensor compatibility and programming for your 2017 SQ5. Some wheels need specific valve stems or sensor mounts.
• Condition: inspect used wheels for bends, cracks, prior repairs, and corrosion on the hub pad.

Plus Sizing And Common Upgrades

Plus sizing means increasing wheel diameter and reducing tire sidewall height to keep overall diameter similar. Minus sizing is the opposite for more sidewall and winter traction. Because actual clearances can vary by option package and brake size, verify each change with the calculator and an in-person test fit before driving.

• Plus sizing process: increase rim diameter by 1 step, then reduce tire aspect ratio to keep overall diameter close to stock. Use the calculator to compare diameter, inner clearance, and outer poke.
• Minus sizing process: decrease rim diameter, increase aspect ratio to maintain overall diameter, and verify brake caliper clearance.
• Width changes: if you go wider than 8.5 inches, check both sides of the wheel path. Small offset tweaks may be needed to balance inner and outer clearance.
• AWD caution: keep front and rear tire diameters matched to avoid drivetrain stress. Rotate tires regularly to keep tread depths even.

Installation Tips

• Test fit each wheel without a tire first if possible. Spin by hand to verify caliper and suspension clearance.
• Clean the hub face and center pilot. Remove rust and debris. Apply a very light film of anti-seize on the hub pilot only, not on the wheel mating face.
• Use hub-centric rings if the wheel center bore is larger than 66.6 mm. Seat the ring fully before mounting.
• Hand start all M14 x 1.5 fasteners to avoid cross-threading. Tighten in a star pattern.
• Torque to the specification in your owner manual using a calibrated torque wrench. Re-torque after 50 to 100 miles.
• If using spacers, ensure they are hub-centric and that you have appropriate extended fasteners. Re-check torque more frequently at first.
• Set tire pressures to the door placard values. Perform an alignment check if you changed wheel width or offset significantly.

Tools And Helpful Supplies

• Torque wrench, 1/2 inch drive: Search on Amazon
• Thin wall lug socket set for tight spoke wheels: Search on Amazon
• Hub-centric rings, 66.6 mm outer diameter: Search on Amazon
• Wheel hanger guide pin, M14 x 1.5: Search on Amazon

FAQs

Will 5x112 wheels from another vehicle fit my 2017 Audi SQ5?
Only if all critical specs work together. Bolt pattern must be 5x112, center bore must be 66.6 mm or larger with rings, offset and width must clear brakes, suspension, and fenders, and M14 x 1.5 fasteners must seat correctly. Always verify with the calculator and a test fit.

Do I need hub-centric rings?
If the wheel’s center bore is larger than 66.6 mm, yes. Choose rings with 66.6 mm outer diameter and the correct inner diameter to match the wheel bore. If the wheel bore is smaller than 66.6 mm the wheel will not fit.

What offset will work?
The known OEM offset is ET33. Use the calculator to compare any new offset to ET33 and check inner and outer clearances. Avoid large changes that push the wheel too far inward or outward.

What tire sizes keep the speedometer accurate?
Start from 255/45R20 and use the calculator to find alternatives with similar overall diameter. Keep the diameter change small to protect the speedometer and driver assistance systems.

Do I need new lug bolts or nuts?
Match the M14 x 1.5 thread size and the wheel’s seat profile. If you add spacers, use appropriately longer fasteners. Verify thread engagement and seat type before driving.

What is the correct torque for the fasteners?
Torque varies by wheel material and OEM guidance. Refer to the owner manual or Audi service information for the exact torque for your 2017 SQ5. Do not guess.

Can I run staggered wheel or tire sizes?
Check AWD constraints. Front and rear overall tire diameters should match to avoid drivetrain stress. If you change widths, ensure clearances and keep rolling circumference equal front to rear.