2008 Dodge Dakota Wheel Interchange

2008 Dodge Dakota Wheel Fitment and Interchange

Known OEM Fitment For 2008 Dodge Dakota

The following specifications are the known OEM fitment values provided for the 2008 Dodge Dakota. They should be treated as a baseline, not as proof that every trim, package, or replacement wheel will fit. Confirm the vehicle configuration, wheel markings, and OEM documentation before purchasing.

The supplied tire dimensions correspond to a 245/70R16 size format. Before using that size, verify the tire placard on the vehicle and the owner’s manual for the specific Dakota configuration. A wheel must match the 5x139.7 bolt pattern, provide suitable clearance, and use the correct M14 x 1.5 wheel hardware. Do not assume that a wheel fits solely because its bolt pattern matches.

Center bore is also important. A wheel with a smaller center bore than 77.8 mm will not seat over the hub. A larger-bore wheel may require correctly sized hub-centric rings where appropriate, but the ring material, fit, and wheel design must be suitable for the application. Confirm all dimensions with the wheel manufacturer and OEM sources.

How To Use The Wheel Interchange Calculator

Use the calculator to compare a prospective donor wheel and tire with the equipment installed on your 2008 Dodge Dakota. Enter the donor vehicle or donor wheel information in the “Wheels from” area, then select or enter the Dakota as the vehicle in the “Installed on” area. Review the calculated differences in diameter, width, offset, and related clearance measurements.

The calculator also allows custom wheel and tire entries. Use “Custom wheel size” to change rim diameter, rim width, or offset. Use “Custom tire size” to change section width or aspect ratio. When rim diameter changes, the calculator updates the tire diameter in the comparison, so review the resulting tire dimensions rather than looking only at the wheel diameter.

Use the calculator as a screening tool, not as a substitute for a physical test fit. It cannot confirm every brake-caliper, suspension, fender, tire-chain, steering-lock, or body-clearance condition. If a donor vehicle or trim is not listed, compare its measured specifications with the known Dakota values above and confirm them through the donor vehicle manufacturer, wheel manufacturer, or OEM service information.

Fitment Checklist Before You Buy

Start with the complete specification, including bolt pattern, center bore, diameter, width, offset, backspacing, wheel load rating, and the intended tire size. For this 2008 Dodge Dakota baseline, the bolt pattern is 5x139.7, the center bore is 77.8 mm, the thread size is M14 x 1.5, and the listed wheel is 16x7 with ET25 and 4.48-inch backspacing.

• Confirm the wheel has five mounting holes on a 139.7 mm pitch circle.
• Confirm the center bore is not smaller than the vehicle hub measurement.
• Check wheel load rating against the vehicle’s required axle loads and the wheel maker’s application guidance.
• Compare offset and backspacing with the calculator, then inspect inner suspension and brake clearance.
• Check outer fender, mudguard, steering, and full-suspension-travel clearance with the tire installed.
• Verify that the tire’s load index, speed rating, diameter, and width are appropriate for the vehicle.
• Confirm the wheel uses compatible M14 x 1.5 hardware and the correct seat design, such as conical or spherical, as specified by the wheel manufacturer.
• Check whether the vehicle uses tire-pressure monitoring sensors and whether the replacement wheels and sensors support the system.
• Obtain the required torque specification from the owner’s manual or an OEM service source. Do not guess the torque value.

Trim-level and package differences may affect brake, suspension, and fender clearance. If a specification is not shown here, it is unknown from the supplied data and should be confirmed before ordering.

Plus Sizing And Common Upgrades

Plus sizing changes the wheel diameter while maintaining a similar overall tire diameter by using a shorter tire sidewall. It can alter ride comfort, impact protection, steering feel, speedometer behavior, wheel weight, and clearance. The calculator can help compare a custom rim diameter, width, and offset with the listed 16x7 ET25 baseline.

Do not select a larger wheel based on diameter alone. A wider wheel or a different offset can move the inner rim closer to suspension components or move the tire outward toward the fender. A larger tire can also affect steering clearance and suspension travel. Confirm the complete wheel and tire assembly, including section width and actual manufacturer dimensions.

There is no single upgrade size that can be confirmed for every 2008 Dodge Dakota from the information provided. Use the calculator to model the proposed dimensions, then verify the tire manufacturer’s approved rim-width range, wheel load rating, and physical clearance on the vehicle.

Installation Tips

Inspect each replacement wheel for cracks, bends, corrosion, damaged mounting seats, and incorrect hardware requirements before installation. Clean rust and debris from the hub and wheel mounting surfaces without removing excess hub material. The wheel should sit flush against the hub or approved spacer surface with no rocking or interference.

Install only compatible lug hardware. M14 x 1.5 describes the thread size, but it does not identify the required lug-seat shape or the correct nut dimensions. Use the hardware specified by the wheel manufacturer, start the nuts by hand, and tighten them in a star pattern. Apply the vehicle or wheel manufacturer’s specified torque with a calibrated torque wrench, not an assumed value.

After installation, rotate each wheel by hand where safe and check for contact. Lower the vehicle, recheck torque according to the applicable service instructions, and inspect clearance at steering lock and through available suspension travel. Recheck fastener torque after the initial driving period if required by the wheel manufacturer. Stop driving if you notice vibration, rubbing, looseness, or loss of tire pressure.

Tools And Helpful Supplies

Useful equipment includes a calibrated torque wrench, a suitable socket set, a jack and jack stands or an appropriate vehicle lift, a tire-pressure gauge, and a tread-depth or clearance measuring tool. Use jack stands or a lift rated for the vehicle and follow safe lifting points from the owner’s manual.

A hub and wheel mounting-surface brush can help remove loose corrosion, while a thread pitch gauge can help verify hardware when the correct fasteners are uncertain. For shopping, see automotive torque wrenches on Amazon and wheel bolt pattern gauges on Amazon. These tools do not replace the wheel manufacturer’s specifications or an OEM service procedure.

FAQs

What is the bolt pattern for the 2008 Dodge Dakota?

The known bolt pattern provided for the 2008 Dodge Dakota is 5x139.7. Match the full fitment, including center bore, offset, wheel load rating, and hardware, rather than relying on bolt pattern alone.

What is the center bore for the 2008 Dodge Dakota?

The known center bore is 77.8 mm. A wheel with a smaller bore cannot fit over the hub. A larger bore may need an appropriate hub-centric solution, subject to the wheel manufacturer’s instructions.

What wheel size is listed for this 2008 Dodge Dakota?

The supplied baseline lists a 16-inch diameter and 7.0-inch width, with ET25 offset and 4.48-inch backspacing. Confirm the specific vehicle trim and existing wheel markings before treating these values as the required size for your truck.

What tire size is represented by the supplied tire measurements?

The supplied measurements represent a 245/70R16 format: 245 mm section width, 70 percent aspect ratio, and a 16-inch rim diameter. Verify the door-jamb tire placard, owner’s manual, tire load index, and the tire manufacturer’s approved rim width before installation.

Can wheels from another vehicle fit the 2008 Dodge Dakota?

They may fit only if all critical specifications and clearances are compatible. Compare the donor wheel in the calculator, including diameter, width, offset, backspacing, bolt pattern, and center bore. Then confirm brake and suspension clearance with a physical inspection and consult OEM or wheel-maker fitment information.

Does a matching bolt pattern guarantee wheel fitment?

No. A matching bolt pattern does not confirm center-bore compatibility, brake clearance, offset, backspacing, lug-seat compatibility, wheel load rating, or tire clearance. Those items must be checked before purchase and installation.

Can I use a custom wheel size in the calculator?

Yes. Enter custom rim diameter, rim width, and offset under “Custom wheel size,” then enter the proposed tire section width and aspect ratio under “Custom tire size.” Changing rim diameter updates the tire diameter comparison. Treat the result as guidance and verify the actual wheel and tire dimensions before driving.