2008 Dodge Durango Wheel Interchange

2008 Dodge Durango Wheel Fitment and Interchange Guide

Use this guide to review the supplied OEM wheel and tire information for the 2008 Dodge Durango. Fitment can vary by trim, package, suspension setup, brake equipment, and replacement parts. Confirm every measurement on your vehicle before purchasing wheels or tires.

Known OEM Fitment For 2008 Dodge Durango

The following specifications are the known OEM fitment values available for this page. They should be treated as a reference, not as a substitute for checking the vehicle and the wheel manufacturer’s specifications.

The listed 245/70R17 tire has an approximate calculated overall diameter of 30.5 inches. Actual tire dimensions can differ by brand, tread design, inflation pressure, and approved measuring method. Do not assume that every 2008 Durango trim uses exactly the same wheel or tire specification unless it is confirmed through the vehicle placard, owner’s manual, service information, or the original wheel.

How To Use The Wheel Interchange Calculator

Use the calculator to compare a donor vehicle’s wheels with the wheels installed on your 2008 Dodge Durango. Enter the donor wheel and tire measurements in “Wheels from” and enter the Durango measurements in “Installed on.” Compare rim diameter, rim width, offset, tire section width, aspect ratio, and calculated tire diameter.

You can also select “Custom wheel size” to test a wheel diameter, width, and offset that is not already represented by a donor vehicle. Use “Custom tire size” to evaluate a different section width and aspect ratio. When you change the rim diameter, the calculator updates the tire diameter in the comparison, which helps show whether the proposed tire maintains a similar overall diameter.

A calculator result is a dimensional comparison, not an approval of load capacity, brake clearance, steering clearance, suspension clearance, or tire legality. Confirm those items physically and with OEM or wheel and tire manufacturer documentation before installation.

Fitment Checklist Before You Buy

Match the 5x139.7 bolt pattern and verify that the wheel’s center bore is compatible with the vehicle hub. A larger center bore may require correctly specified hub-centric rings, while a smaller center bore will not fit over the hub. Confirm that the replacement wheel accepts M14 x 1.5 hardware and that the wheel maker specifies suitable nuts or bolts for the wheel’s seat design.

Compare the proposed width and offset with the known 7.5-inch width and ET35 reference. A change in offset can move the wheel inward toward suspension components or outward toward the fender. Check inner clearance to the strut, control arms, brake components, and steering parts, as well as outer clearance at full steering lock and through the complete suspension movement.

Verify the wheel’s load rating, the tire’s load index and speed rating, valve stem requirements, pressure monitoring equipment if fitted, and the tire manufacturer’s approved rim-width range. Inspect the actual vehicle for prior modifications, spacers, lift components, brake changes, or damaged hubs. If any measurement is uncertain, stop and obtain confirmation from a qualified technician.

Plus Sizing And Common Upgrades

Plus sizing generally means using a larger wheel diameter with a lower-profile tire while attempting to keep the overall tire diameter close to the original reference. This can change ride comfort, road noise, steering response, wheel protection, tire cost, and the risk of impact damage. It may also affect speedometer behavior and the available clearance.

Do not select a plus-size tire by diameter alone. Use the calculator to compare the custom wheel and tire dimensions, then verify the tire manufacturer’s approved rim width, load requirements, and clearance. A wider tire can contact the suspension or fender even when its calculated diameter appears acceptable. The correct replacement is also dependent on the wheel’s load rating and brake clearance, which the calculator cannot certify.

Because a complete trim-by-trim upgrade list was not provided, no specific alternative wheel or tire sizes should be assumed to fit every 2008 Dodge Durango. Use the original door-jamb placard and OEM documentation as the baseline for your particular vehicle.

Installation Tips

Before mounting, compare the replacement wheel with the original for bolt pattern, center-bore fit, offset, width, brake clearance, and hardware seat type. Clean rust and debris from the hub mounting face without removing metal. Never force a wheel onto a smaller center bore, and do not use random spacers or adapters to correct an unknown fitment problem.

Install tires only on wheels within the tire manufacturer’s approved width range. Inflate the tires to the vehicle manufacturer’s recommended pressure, not the maximum pressure molded on the tire sidewall. Tighten the wheel hardware in a star pattern with a calibrated torque wrench using the vehicle or wheel manufacturer’s specified torque. The correct torque value was not provided here, so confirm it through the owner’s manual, service information, or a Dodge service source.

After installation, check for free rotation and clearance with the steering turned fully left and right. Test carefully at low speed, then recheck the hardware after the initial driving period according to the vehicle or wheel manufacturer’s instructions. Stop immediately if you notice rubbing, vibration, pulling, noise, or loose hardware.

Tools And Helpful Supplies

Useful supplies include a calibrated torque wrench, appropriate M14 x 1.5 wheel hardware, a socket that correctly fits the hardware, a tire-pressure gauge, a tread-depth gauge, a flashlight, and a wire brush or approved hub-cleaning tool. A hub and wheel measuring tool can help confirm center bore and offset, but measurements should be checked against manufacturer documentation.

View automotive torque wrenches on Amazon and view digital tire pressure gauges on Amazon. Product compatibility, accuracy, and suitability should be confirmed before purchase.

FAQs

What is the bolt pattern for the 2008 Dodge Durango?
The known bolt pattern for this page is 5x139.7. Confirm the specification against the original wheel or reliable OEM service information before buying.

What is the center bore?
The known center bore is 77.8 mm. A wheel with a smaller bore will not fit over the hub. A larger bore may need correctly sized hub-centric rings if approved for the application.

What wheel offset is listed?
The known wheel offset is ET35, or positive 35 mm, with a listed backspacing of 5.13 inches. Different offsets change the wheel’s position and must be checked for inner and outer clearance.

What is the known OEM tire size?
The known tire size is 245/70R17, with a 245 mm section width, a 70 percent aspect ratio, and a 17-inch rim diameter. Trim-specific differences were not provided, so verify the placard on your vehicle.

Can I install wheels from another vehicle?
Only if the donor wheel matches the required bolt pattern, center-bore requirements, hardware, load rating, brake clearance, width, offset, and tire requirements. Use the calculator for dimensional comparison, but do not treat a calculator match as a complete safety approval.

Can I use a different wheel diameter?
You can evaluate a different diameter with the custom wheel size and custom tire size controls. Changing the rim diameter updates the tire diameter comparison. Confirm tire load capacity, approved rim width, speed rating, clearance, and local requirements before installation.

What should I do if the calculator shows a close match?
A close dimensional result still requires an inspection. Confirm the actual wheel, tire, hub, brake, suspension, steering, and fender clearances on the vehicle. If the result is uncertain or any component rubs, do not install the combination.

Does this page list every compatible vehicle or trim?
No. Only the supplied 2008 Dodge Durango fitment values are presented here. Compatible donor vehicles and trim-specific alternatives should be confirmed through OEM sources, the wheel manufacturer, and the on-page calculator.