2011 Dodge Journey Wheel Interchange

2011 Dodge Journey Wheel Interchange, Specs, and Fitment Guide | wheelinterchange.com

Known OEM Fitment For 2011 Dodge Journey

The 2011 Dodge Journey was offered with multiple factory wheel and tire packages depending on trim and options. The values below are the known items from the available data. If a value is missing or appears to conflict, it likely varies by trim. Confirm your exact specs using the on-page calculator, your door-jamb tire label, and OEM sources.

What this means for you:

• Any replacement or donor wheel must be 5x127 and must center on a 71.6 mm hub, either natively or with hub-centric rings.
• Hardware must be M14 x 2.00 and the lug seat style must match the wheel design.
• Offset near +40 mm keeps a stock-like stance on packages similar to the 18x7 ET40 example. Verify inner and outer clearance with the calculator before buying.

If your vehicle’s door placard shows a different wheel or tire size than the examples above, follow the placard and owner’s manual for OEM specifications, then use the calculator to compare any potential upgrade.

How To Use The Wheel Interchange Calculator

• Set Installed on (your vehicle) to 2011 Dodge Journey.
• Pick a donor vehicle or enter a Custom wheel size and Custom tire size to represent what you want to install.
• Adjust rim diameter, width, and offset. When you change rim diameter, the tire diameter in the comparison updates so you can keep overall diameter consistent.
• Review inner clearance to the strut and brake components. Positive offset moves the wheel inboard. More backspacing also moves inboard.
• Review outer clearance to the fender and bumper. Lower offset or more width increases poke.
• Check overall tire diameter difference and speedometer error. Aim to keep total diameter change small, commonly within about 3 percent, unless you are recalibrating.
• Confirm center bore and hardware. If the donor wheel bore is larger than 71.6 mm, plan on hub-centric rings to 71.6 mm and matching M14 x 2.00 hardware with the correct seat.

Fitment Checklist Before You Buy

• Bolt pattern is 5x127. Do not attempt 5x114.3 or 5x120.
• Center bore must seat on 71.6 mm. Use rings if the wheel bore is larger. Do not use a wheel with a smaller bore.
• Thread size is M14 x 2.00. Match the lug seat style to the wheel design. Do not mix conical and ball seats.
• Offset and backspacing must clear struts, knuckles, and fenders. Start from the known ET40 example and validate changes with the calculator and a physical test fit.
• Wheel diameter and brake clearance can vary by trim. Larger brakes need more spoke clearance. Test fit one front wheel before mounting tires.
• Overall tire diameter should stay close to stock unless you confirm speedometer and ABS tolerance.
• Load index and speed rating must meet or exceed the values on your door placard.
• TPMS: plan to transfer sensors or install compatible new ones and perform relearn as required by your vehicle.
• Spare tire well and chain clearance. If you use snow chains, verify clearance at full lock and compression.
• Verify return policy for mounted tires. Most shops will not accept returns once tires are installed.

Plus Sizing And Common Upgrades

The Journey platform can be tuned toward comfort or handling by altering wheel diameter, width, and tire profile. Because trims varied in 2011, there is no single upgrade that fits every vehicle. Use these guidelines with the calculator and a test fit:

• Diameter changes: Moving up in wheel diameter reduces tire sidewall for crisper steering but can increase impact harshness. Keep overall tire diameter near stock to maintain speedometer accuracy and transmission shift logic.
• Width and offset: A wider wheel improves lateral grip if the tire width increases to match. Maintain inner clearance to the strut and outer clearance to the fender. Small offset reductions can add outer poke but reduce inner clearance.
• Tire choices: Choose load index that meets or exceeds the door placard. Touring all-season tires ride softer. Performance all-seasons or summers improve grip but can ride firmer.
• Hub centering: If you select aftermarket wheels with a larger center bore, always use quality hub-centric rings sized to 71.6 mm to minimize vibration.

The provided data includes an 18x7 ET40 wheel example and a 225/70R16 tire example, which indicates multiple OEM setups. Confirm your starting point from your tire label, then compare potential +1 or +2 options in the calculator to check clearances and diameter.

Installation Tips

• Test fit the bare wheel on the front hub first. Spin by hand to confirm spoke and barrel clearance to calipers and knuckle.
• Clean the hub face and the wheel mounting pad. Remove rust and debris so the wheel seats flat. Do not apply grease to the seating surfaces.
• If using hub-centric rings, make sure they seat fully on the hub and in the wheel bore before tightening hardware.
• Install lug nuts by hand first to avoid cross-threading. Do not lubricate studs or nuts unless the OEM specifically instructs it.
• Tighten in a star pattern in stages and torque to the specification in your owner’s manual. Re-torque after 50 to 100 miles.
• Verify thread engagement. Ensure sufficient turns of engagement for M14 x 2.00 hardware and that the lug seat matches the wheel.
• After installation, turn the steering wheel lock to lock and drive over a few bumps to check for rubbing under load.
• Transfer or program TPMS sensors as required and set tire pressures to the values on the door placard.

Tools And Helpful Supplies

• 1/2 inch drive torque wrench for accurate torque
• M14x2.0 lug nuts with the correct seat for your wheels
• 71.6 mm hub-centric rings if your aftermarket wheel bore is larger
• 3 ton jack stands for safe support

FAQs

• What is the bolt pattern for the 2011 Dodge Journey?

  5x127. Any replacement wheel must match this pattern.

• What center bore do I need?

  71.6 mm at the hub. If the wheel bore is larger, use hub-centric rings sized to 71.6 mm. Do not attempt to force a smaller bore onto the hub.

• What is the correct thread size and lug nut type?

  M14 x 2.00 thread. The seat style must match the wheel, commonly conical on many aftermarket wheels. Follow the wheel maker’s requirement and your owner’s manual.

• Will 18 inch wheels fit my 2011 Journey?

  An 18x7 ET40 wheel is listed in the known data for some trims. Other trims used different sizes such as 16 inch with 225/70R16 tires. Check your door placard to confirm your OEM size, then use the calculator to verify clearance for 18 inch wheels on your specific trim and brakes.

• What offset should I choose for aftermarket wheels?

  Use the ET40 example as a baseline, then compare inner and outer clearance with the calculator. The safe range depends on wheel width, tire choice, and your brake package.

• Can I use 5x127 wheels from a different vehicle?

  Possibly, if center bore is 71.6 mm or larger with rings, the offset and width clear your brakes and fenders, and the load rating is adequate. Always test fit and verify with the calculator.

• Do I need to change TPMS sensors?

  If reusing your original wheels, no change is needed. If changing wheels, either transfer your sensors or install compatible new ones and perform the relearn procedure specified for your vehicle.

• What torque should I use on the lug nuts?

  Refer to the torque specification in your owner’s manual or OEM service information for the 2011 Dodge Journey. Do not guess. Re-torque after 50 to 100 miles.