2016 Dodge Journey Wheel Interchange

2016 Dodge Journey Wheel Fitment Guide | wheelinterchange.com

Known OEM Fitment For 2016 Dodge Journey

Below are factory specifications that are confirmed for at least one 2016 Dodge Journey configuration. Trims and packages can vary. If your trim is different or a value is missing, use the on-page calculator to compare and confirm, and verify against your owner’s manual, the tire placard on the driver’s door jamb, or OEM parts catalogs by VIN.

Important: The 19 in wheel specification and the 225/65R17 tire specification may correspond to different factory packages. If your Journey currently has a different wheel or tire size, treat the values above as references and confirm exact equipment by checking your tire placard and VIN-specific OEM parts information.

How To Use The Wheel Interchange Calculator

The calculator lets you compare a donor vehicle’s wheel and tire setup against your 2016 Dodge Journey, and also test custom sizes safely before you buy.

• Open the calculator and select "Installed on" as 2016 Dodge Journey.
• If you know your current setup, enter it in "Your vehicle" or click the OEM preset if shown.
• To compare a donor wheel, enter that wheel’s diameter, width, and offset in "Wheels from".
• Use "Custom wheel size" to try alternate rim diameter, width, and offset. The model will recalculate inner and outer clearance changes.
• Use "Custom tire size" to set section width and aspect ratio. When you change rim diameter, the tire diameter comparison updates automatically.
• Review:
  • Inner clearance to strut and suspension
  • Outer poke relative to fender
  • Overall tire diameter difference and speedometer impact
• Keep overall tire diameter change small. As a general check, many installers aim to keep overall diameter within a few percent of stock. Always confirm ride height and clearance on your vehicle.

Fitment Checklist Before You Buy

• Match bolt pattern: 5x127 must be exact.
• Center bore: Vehicle hub is 71.6 mm. Aftermarket wheels with a larger bore may require hub-centric rings sized to your wheel’s bore. Do not force a smaller-bore wheel onto the hub.
• Thread size: M14 x 2.00. Verify lug nut seat type and required length per wheel manufacturer.
• Offset and width: Compare your target wheel against your current setup using the calculator. Confirm inner clearance to struts/springs and outer clearance to fenders and liners through full steering and compression.
• Brake clearance: Spoke design and barrel shape matter. Test-fit to confirm caliper clearance.
• Tire sizing: Use the calculator to maintain appropriate overall diameter and load index. Verify load/speed ratings meet or exceed OEM.
• Sensors: If reusing TPMS, confirm compatibility and torque for sensor hardware.
• Spare fitment: Changing sizes may affect spare-tire well storage and rotation plans.

Plus Sizing And Common Upgrades

The Journey has been offered with multiple factory wheel and tire packages. Our known values show at least a 19x7.5 ET38 wheel on some trims and a 225/65R17 tire on others. If you are exploring a different size:

• Use the calculator starting from your actual current size taken from the door placard or your existing tire sidewall.
• Adjust rim width and offset to keep inner clearance safe and avoid excessive poke. Small changes in offset can have a big effect on clearance.
• Adjust tire section width and aspect ratio so overall diameter remains close to stock for speedometer and ABS stability. Confirm real-world clearance by test fitting.
• If selecting aftermarket wheels with a larger center bore, plan for hub-centric rings sized to your specific wheel model to maintain hub-centric mounting.

Because fitment can vary by trim, brakes, and suspension, confirm all measurements on your vehicle before purchasing.

Installation Tips

• Test fit each front and rear wheel without tires first if possible. Spin by hand and check caliper, knuckle, and strut clearance.
• Clean the hub face and center pilot with a wire brush. Remove rust and debris for proper seating.
• If using hub-centric rings, install them fully seated in the wheel bore.
• Hand-thread M14 x 2.00 lug nuts to avoid cross-threading. Tighten in a star pattern.
• Torque to the value in your owner’s manual or service information for your exact trim and wheel type. Re-torque after 50–100 miles.
• Verify no rubbing at full steering lock and over bumps. Inspect inner fender liners and brake hoses.
• Check TPMS function and update tire pressure to the placard values unless your new tire load rating requires different pressures as specified by the tire manufacturer.

Tools And Helpful Supplies

• 1/2 inch drive torque wrench
• M14x2.00 lug nuts (verify seat type and length for your wheels)
• Digital caliper for measuring center bore and stud diameter
• Anti-seize lubricant for the hub face and light use on wheel center bores if recommended

FAQs

• What is the bolt pattern for the 2016 Dodge Journey?

  It is 5x127. This must match your replacement wheels exactly.

• What center bore do I need for the Journey?

  The vehicle hub bore is 71.6 mm. Wheels with a larger bore can be used with properly sized hub-centric rings. Wheels with a smaller bore will not fit.

• What is the thread size for the lug nuts?

  M14 x 2.00. Confirm the correct lug nut seat type for your specific wheel design before purchasing.

• Which OEM wheel and tire sizes are factory for 2016?

  Our confirmed data shows a 19x7.5 wheel with ET38 on some trims and a 225/65R17 tire on others. Packages vary by trim. Check your door-jamb placard, owner’s manual, or OEM parts by VIN to verify your exact factory size.

• Can I use the calculator to see if a different offset will clear my brakes?

  Yes. Enter your current setup and the proposed wheel’s width and offset. Review inner clearance changes to the strut and caliper. Always test fit to confirm spoke and barrel clearance.

• How close should the new tire’s overall diameter be?

  Use the calculator to compare overall diameter. Installers commonly aim to keep overall tire diameter changes small to maintain speedometer accuracy and avoid electronic system issues. Confirm on-vehicle clearance through full steering and suspension travel.

• What torque should I use on the lug nuts?

  The correct torque can vary by trim and wheel material. Use the value in your owner’s manual or OEM service information for your exact configuration, and re-torque after initial driving.