2018 Dodge Journey Wheel Interchange

2018 Dodge Journey Wheel Fitment and Interchange Guide

Known OEM Fitment For 2018 Dodge Journey

The values below are the factory specifications we have for the 2018 Dodge Journey. Some trims and option packages used different wheel and tire sizes. If a value is not listed for your exact trim, or appears to conflict, use the on-page calculator and verify against your owner’s manual, the tire placard on the driver’s door jamb, or an OEM parts catalog before purchasing.

Note: The wheel and tire data above indicate that multiple OEM wheel packages were available in 2018. For example, 225/65R17 tires fit a 17 inch rim, while a separate package used 19x7.5 ET38 wheels. This is normal across trims. Confirm which package your specific Journey has using the door-jamb tire placard and the calculator on wheelinterchange.com.

How To Use The Wheel Interchange Calculator

The calculator on wheelinterchange.com lets you compare a donor vehicle’s wheels to your 2018 Dodge Journey and test custom sizes safely.

• Step 1 - In the Wheels from (donor vehicle) panel, enter the donor wheel and tire specs. If you only know the wheel size, enter that and leave the tire blank.
• Step 2 - In the Installed on (your vehicle) panel, select 2018 Dodge Journey and confirm the OEM specs that match your trim. If your trim differs, type in the values from your door placard or owner’s manual.
• Step 3 - Use Custom wheel size to try different rim diameters, widths, and offsets. Width and offset changes will update poke, backspacing, inner clearance, and scrub relationship.
• Step 4 - Use Custom tire size to adjust section width and aspect ratio. Changing rim diameter will automatically update overall tire diameter for the comparison.
• Step 5 - Review the results for inner clearance to struts and brakes, outer poke relative to fender, and tire diameter variance. Aim to keep tire diameter close to stock so your speedometer and ABS behavior remain predictable.
• Step 6 - If any dimension shows a potential interference, revise the custom width or offset until the calculator shows safe clearances.

Fitment Checklist Before You Buy

• Bolt pattern must be 5x127 mm. 5x120 or 5x114.3 will not fit.
• Center bore must be 71.6 mm or larger. If the wheel bore is larger, use hub-centric rings to step down to 71.6 mm.
• Thread size is M14 x 2.00. Use matching nuts or bolts with the correct seat type as specified by the wheel manufacturer. Do not mix conical and ball seats.
• Offset and width must clear the front calipers and suspension on the inside and the fenders on the outside. Verify with the calculator.
• Tire overall diameter should stay close to OEM. As a general rule, keep variance small to maintain speedometer accuracy and prevent rubbing. Use the calculator’s diameter comparison.
• Load rating of wheels and tires must meet or exceed the Journey’s GAWR. Check wheel and tire manufacturer ratings.
• TPMS: Plan to transfer sensors or install compatible replacements and perform relearn as required by Dodge.
• Backspacing figures can vary with measurement method. Rely on the calculator’s inner clearance metrics and a physical test fit.
• Brake and hub clearance: test fit the front wheels first to confirm barrel and spoke clearance over calipers and that the hub seats fully.

Plus Sizing And Common Upgrades

The Journey was offered with multiple factory packages, including 17 inch tires as well as larger OEM wheels. If you plan to plus size:

• Use the calculator to keep overall tire diameter close to stock to protect ABS, traction control, and gearing feel.
• As width increases, you often need a different offset to maintain inner clearance and avoid fender poke. Adjust offset in small steps and recheck clearances.
• Confirm brake clearance. Larger-diameter wheels usually clear more easily, but spoke design still matters.
• If using aftermarket wheels with a larger center bore than 71.6 mm, add hub-centric rings to minimize vibration.
• When changing wheel diameter, select a tire aspect ratio that keeps diameter consistent. The calculator updates this for you during comparisons.

Installation Tips

• Safety first: park on level ground, use wheel chocks, and support the vehicle with rated jack stands.
• Clean the hub face and the new wheel mounting pad. Remove rust and debris so the wheel seats flush.
• If the wheel bore is larger than 71.6 mm, install hub-centric rings before mounting.
• Hand start all lug nuts to avoid cross-threading the M14 x 2.00 studs.
• Tighten in a star pattern and use a calibrated torque wrench. Follow the torque specification in your owner’s manual or OEM service information. Recheck torque after a short shakedown drive.
• Verify caliper and suspension clearance by slowly rotating the wheel by hand before driving.
• After installation, monitor for vibration. If present, check ring fitment, wheel balance, and torque.

Tools And Helpful Supplies

• 1/2 inch drive torque wrench
• M14x2.0 thread chaser
• Wheel chocks
• 71.6 hub-centric rings

FAQs

• Is 5x127 the same as 5x5?

  Yes. 5x127 mm equals 5x5 inches and describes the same bolt pattern used on the 2018 Journey.

• Why do I see both 19 inch wheels and 225/65R17 tires listed?

  Different trims and option packages used different OEM wheel and tire sizes in 2018. Verify your exact package from the door-jamb tire placard or owner’s manual, then use the calculator to model changes.

• What offset should I use with wider aftermarket wheels?

  Offset depends on wheel width, spoke design, and brake clearance. Use the calculator to adjust width and offset together and check inner and outer clearance. Do not rely on a single “one size fits all” offset.

• Do I need hub-centric rings on the Journey?

  If your aftermarket wheels have a center bore larger than 71.6 mm, yes. Use rings that reduce the wheel bore to 71.6 mm so the wheel centers on the hub and runs smoothly.

• Can I use wheels with a different bolt pattern like 5x120 or 5x114.3?

  No. Only wheels with the correct 5x127 pattern should be used. Adapters introduce additional variables and should only be considered with careful measurement and quality components.

• Will my TPMS sensors work with new wheels?

  Yes, you can transfer the existing sensors or install compatible replacements. Follow Dodge procedures for sensor service and relearn. Valve stem type and torque should follow OEM or sensor manufacturer instructions.

• What is the correct lug nut torque for the 2018 Journey?

  Refer to the owner’s manual or an OEM service source for the exact specification. Always use a torque wrench and retorque after initial driving.