2009 Ford Edge Wheel Interchange and Fitment Guide
Use this guide to compare replacement wheels and tires for a 2009 Ford Edge. The known measurements below are provided fitment data, but equipment can vary by trim, package, wheel design, and market. Confirm every measurement with the vehicle door-jamb label, the original wheel markings, the owner's manual, and Ford OEM parts information before ordering.
Known OEM Fitment For 2009 Ford Edge
The following specifications are the known data available for this page. They should be treated as a reference, not as permission to assume that every listed measurement belongs to one original wheel and tire combination.
| Specification |
Known value |
| Bolt pattern |
5x114.3 |
| Center bore |
70.5 mm |
| Thread size |
M14 x 2.00 |
| Rim diameter |
20 inches |
| Rim width |
8.5 inches |
| Wheel offset |
ET42, or 42 mm |
| Backspacing |
5.9 inches |
| Tire section width |
235 mm |
| Tire aspect ratio |
65 percent |
| Tire rim diameter |
R17, or 17 inches |
Notice that the supplied rim diameter is 20 inches while the supplied tire rim diameter is 17 inches. These values may describe different configurations, or the source data may be incomplete. Do not combine them into a single assumed package. Check the tire sidewall and wheel stamp on your Edge, then use the calculator to model the exact wheel and tire sizes you intend to install.
How To Use The Wheel Interchange Calculator
The on-page calculator lets you compare wheels from a donor vehicle with wheels installed on your vehicle. Start by entering or selecting the donor vehicle and the 2009 Ford Edge as the installed vehicle. Compare bolt pattern, center bore, wheel width, diameter, and offset before considering appearance.
- Use the donor vehicle fields to represent the wheel you want to reuse or purchase.
- Use the installed-on-your-vehicle fields to represent the verified measurements for your Edge.
- Enter custom wheel size values when the donor wheel or proposed replacement does not match a standard selection.
- Adjust rim diameter, rim width, and offset together. A change in one measurement can alter clearance and the wheel's position relative to the suspension and fender.
- Enter custom tire section width and aspect ratio to compare tire dimensions.
- Remember that changing rim diameter updates the tire diameter in the comparison. Confirm that the selected tire is actually manufactured for the chosen rim diameter.
A calculator comparison is a screening tool, not a substitute for a physical test fit. It cannot identify every issue involving brake calipers, spoke shape, hub face variation, tire construction, suspension modifications, or body damage.
Fitment Checklist Before You Buy
- Confirm the 5x114.3 bolt pattern and verify that the wheel has five correctly positioned mounting holes.
- Confirm the 70.5 mm center bore. A wheel bore that is too small will not seat on the hub. A larger bore may require correctly sized hub-centric rings, if appropriate for the wheel design.
- Confirm the wheel's stamped diameter, width, and offset. Do not rely only on an online listing or visual appearance.
- Check that the wheel's load rating meets or exceeds the vehicle and axle requirements listed by Ford or on the vehicle documentation.
- Verify the M14 x 2.00 thread specification and use lug hardware with the correct seat type for the wheel. Thread size alone does not confirm lug-nut compatibility.
- Measure brake-caliper, strut, control-arm, and inner-fender clearance. Spoke clearance can be different even when diameter, width, and offset match.
- Check tire load index, speed rating, inflation requirements, and overall diameter against the vehicle placard and OEM guidance.
- Inspect used wheels for cracks, bends, corrosion around the bead seat, repaired damage, and elongated mounting holes.
- After installation, verify that the tire does not contact the body or suspension at full steering lock and through normal suspension travel.
Plus Sizing And Common Upgrades
Plus sizing means changing wheel diameter while selecting a tire with a lower aspect ratio so the overall tire diameter remains near the original target. It can improve steering response or provide a different appearance, but it also reduces sidewall cushioning and may increase the risk of wheel or tire damage on rough roads.
The known data on this page includes both a 20-inch rim entry and a 17-inch tire rim diameter entry. Because those values do not describe the same mounted tire, use the calculator to compare a complete wheel and tire package rather than copying one value in isolation.
When evaluating a custom setup, compare section width, aspect ratio, calculated tire diameter, wheel width, offset, and backspacing. A wider wheel or a different offset can reduce clearance even if the tire diameter remains similar. Do not use spacers, adapters, or aftermarket lug hardware unless their manufacturer confirms suitability for the vehicle, wheel, load, and intended use.
Installation Tips
- Mount the wheel on a clean hub face. Remove rust and debris without removing hub material.
- Install only the lug nuts or bolts with the correct thread and seat profile for the wheel.
- Start all fasteners by hand to prevent cross-threading.
- Tighten in a star or crisscross pattern, then torque to the Ford-specified value for the vehicle and hardware. The correct torque value is not provided here, so confirm it in the owner's manual or Ford service information.
- Inflate the tires to the pressure shown on the vehicle tire-information label unless a qualified tire professional determines otherwise.
- Spin each wheel by hand when safely lifted and check for contact before lowering the vehicle.
- Recheck lug torque after the first short drive and again according to the wheel manufacturer's instructions.
- Stop driving if there is vibration, rubbing, steering pull, air loss, or unusual noise. Have the installation inspected by a qualified technician.
Tools And Helpful Supplies
Useful equipment includes a torque wrench, suitable socket, jack and jack stands or an approved lift, a tire-pressure gauge, a tread-depth gauge, a hub and wheel measuring tool, and a straightedge for checking wheel markings. Use lifting points and support equipment specified for the vehicle. Never work under a vehicle supported only by a jack.
For tools and wheel-installation supplies, see automotive torque wrenches and wheel lug sockets on Amazon. For measuring hub and wheel dimensions, see wheel fitment measuring tools on Amazon. These links are provided for convenience. Confirm the product specifications and safe working limits before use.
FAQs
What is the bolt pattern for the 2009 Ford Edge?
The known bolt pattern is 5x114.3. Confirm the wheel's mounting-hole pattern before purchase.
What is the center bore?
The known center bore is 70.5 mm. A smaller wheel bore will not fit over the hub, while a larger bore may need an appropriate hub-centric solution.
What wheel thread size is listed?
The known thread size is M14 x 2.00. The correct lug seat style and hardware length must also be verified for the specific wheel.
Can I install any 5x114.3 wheel?
No. Bolt pattern is only one part of fitment. You must also check center bore, diameter, width, offset, backspacing, brake clearance, lug-seat compatibility, load rating, and tire clearance.
Why does this page list both a 20-inch rim and a 17-inch tire rim diameter?
The supplied data contains a 20-inch rim entry and a 17-inch tire rim diameter entry. They may represent different configurations or incomplete source data. Do not assume they are one original package. Verify the markings on your vehicle and model the complete setup in the calculator.
Can I use the calculator as proof that a wheel will fit?
No. The calculator is useful for comparing dimensions and custom wheel and tire sizes, but it cannot replace a physical clearance check or OEM and wheel-manufacturer confirmation.
Will changing rim diameter change tire size?
Yes. In the calculator, changing rim diameter updates the tire diameter in the comparison. Select a tire designed for that rim diameter and verify the resulting diameter, load rating, and clearance.
Where can I confirm the correct tire pressure and lug torque?
Use the tire-information label on the vehicle, the owner's manual, Ford service information, and the wheel or lug-hardware manufacturer's instructions. The exact torque value is not provided in the data for this page.
