2016 Honda Odyssey Wheel Interchange

2016 Honda Odyssey Wheel Interchange and Fitment Guide

Known OEM Fitment For 2016 Honda Odyssey

The following specifications are the currently provided fitment data for the 2016 Honda Odyssey. They may represent only part of the vehicle's available configurations, so confirm the exact equipment on your vehicle before ordering wheels or tires.

Important: the supplied rim diameter is 19 inches, while the supplied tire rim diameter is 17 inches. Those values do not describe one complete wheel-and-tire assembly. Treat them as separate or potentially mixed reference values until you confirm the original tire placard, owner’s manual, wheel markings, and VIN-specific information. Do not mount a 17-inch tire on a 19-inch wheel.

A 5x120 bolt pattern alone does not prove that a donor wheel fits. The center bore, width, offset, brake clearance, load rating, fastener type, and tire size must also be suitable.

How To Use The Wheel Interchange Calculator

Use the calculator to compare a donor vehicle's wheel and tire measurements with the measurements you plan to install on your 2016 Honda Odyssey.

1. Select the donor vehicle under “Wheels from (donor vehicle).” Enter or confirm its rim diameter, rim width, offset, tire section width, and tire aspect ratio.
2. Select the 2016 Honda Odyssey under “Installed on (your vehicle)” and review the comparison against the known values shown above.
3. Use “Custom wheel size” when the donor wheel or your proposed replacement is not represented. Enter diameter, width, and offset rather than relying only on the vehicle name.
4. Use “Custom tire size” to enter the tire section width and aspect ratio. The tire must have the same rim diameter as the wheel on which it will be installed.
5. Review changes in outer position, inner clearance, and overall tire diameter. A smaller numeric offset generally moves a wheel farther outward, while a larger offset generally moves it farther inward, but the calculator is not a substitute for a physical clearance check.
6. Because changing rim diameter updates the tire diameter in the comparison, recheck speedometer effects, fender clearance, suspension clearance, and brake clearance after every size change.

The calculator can identify measurement differences, but it cannot verify every vehicle-specific issue, including brake caliper shape, hub-face condition, stud or nut engagement, tire load index, or body interference under steering and suspension movement.

Fitment Checklist Before You Buy

• Confirm the vehicle's exact wheel and tire specifications from the driver's door-jamb tire label, owner’s manual, Honda service information, or a Honda dealer using the VIN.
• Verify the wheel's 5x120 bolt pattern and make sure the wheel is designed for the correct M12 x 1.5 fastener arrangement.
• Check the wheel center bore against the 64.1 mm reference. A smaller bore will not fit over the hub. A larger bore may require correctly sized hub-centric rings if the wheel manufacturer permits them.
• Compare offset and width with the installed wheel. Confirm both inner clearance to the strut, brake components, and suspension parts and outer clearance to the fender.
• Check wheel load rating and tire load index. They must meet or exceed the vehicle manufacturer's requirements.
• Confirm that the tire's rim diameter matches the wheel's rim diameter. The provided 17-inch tire reference cannot be used on the provided 19-inch rim reference.
• Check tire diameter and width against the calculator, then confirm that the tire does not rub at full steering lock, full jounce, or with passengers and cargo.
• Confirm the replacement wheel accepts the correct lug nuts or bolts, has adequate thread engagement, and uses the seating style specified by the wheel manufacturer.
• Inspect used wheels for cracks, bends, weld repairs, corrosion at the bead seat, and damaged mounting holes.

Plus Sizing And Common Upgrades

Plus sizing changes the wheel diameter while attempting to keep the tire's overall diameter close to the original. This can improve steering response or provide more sidewall support, but it can also reduce ride comfort and increase the risk of wheel and tire damage from potholes.

Do not select a replacement size solely because its diameter appears similar. Compare the complete tire diameter, section width, load index, speed rating, wheel width range, offset, and available brake and body clearance. A wider tire can contact the strut or fender even when its overall diameter is close to the original.

The supplied data includes both a 19-inch rim reference and a 17-inch tire rim reference, so no single plus-size recommendation should be assumed from this page. Use the calculator with the tire size printed on your vehicle's placard, then confirm the result with OEM and tire manufacturer guidance.

Installation Tips

• Install only wheels and tires that have been confirmed for the vehicle's load, clearance, and fastener requirements.
• Clean rust, dirt, and paint buildup from the hub face and wheel mounting surface. Do not apply grease between the wheel and hub face unless the manufacturer specifically instructs you to do so.
• Check that the wheel seats fully against the hub and that the lug nuts or bolts engage correctly without bottoming out.
• Start all fasteners by hand. Tighten them in a star or crisscross pattern, then torque them to the vehicle or wheel manufacturer's specification with a calibrated torque wrench.
• Never use an impact gun as the final torque method.
• After installation, rotate each wheel by hand and check for obvious contact. Lower the vehicle and recheck clearance at steering lock in both directions where practical.
• Recheck fastener torque after the first short drive and again according to the wheel manufacturer's instructions.
• If a tire-pressure monitoring system is fitted, confirm that the sensors are compatible, installed correctly, and relearned according to the vehicle procedure.

Tools And Helpful Supplies

Useful equipment includes a vehicle-rated jack and jack stands, wheel chocks, a properly sized socket, a calibrated torque wrench, a tire-pressure gauge, and a tread or clearance measuring tool. A hub-bore gauge or caliper can help verify wheel dimensions, but the wheel manufacturer's published specifications should remain the primary reference.

Shop automotive torque wrenches on Amazon

Shop automotive wheel chocks on Amazon

Use jack stands on a solid, level surface and follow the vehicle owner's lifting points. Never work beneath a vehicle supported only by a jack.

FAQs

Does a 5x120 wheel automatically fit a 2016 Honda Odyssey?
No. The 5x120 pattern is only one requirement. Center bore, offset, wheel width, brake clearance, load rating, fastener seating, and tire size must also be confirmed.

What center bore is listed for the 2016 Honda Odyssey?
The provided reference is 64.1 mm. Verify the exact requirement using the vehicle's OEM documentation and the wheel manufacturer's specifications before purchase.

What tire size is included in the supplied data?
The supplied tire dimensions are 235 mm section width, 65% aspect ratio, and a 17-inch rim diameter, commonly written as 235/65R17. However, the supplied wheel diameter is 19 inches, so these values should not be treated as one confirmed wheel-and-tire package.

Can I install a 17-inch tire on a 19-inch wheel?
No. The tire bead diameter must match the wheel diameter. A tire marked for a 17-inch rim must be installed on a compatible 17-inch wheel, not a 19-inch wheel.

What does ET45 mean?
ET45 means the wheel has a 45 mm positive offset. Offset affects how far the wheel sits toward the suspension or toward the fender, so width and offset must be evaluated together.

Is the listed 5.77-inch backspacing compatible with the listed wheel measurements?
It is mathematically consistent with an 8-inch-wide wheel and approximately 45 mm positive offset, but you should still confirm the actual marking or published specification for the specific wheel. Manufacturing tolerances and measurement methods can affect the result.

How can I confirm the correct OEM tire and wheel size?
Read the tire-information label on the driver's door area, check the owner’s manual, inspect the tire and wheel markings, and confirm the VIN-specific information with Honda or a qualified tire and wheel professional.

Will the calculator guarantee that a donor wheel will not rub?
No. It compares the entered dimensions and estimates positional changes. Physical inspection is still required to check brake, suspension, hub, strut, fender, and steering-clearance conditions.