2014 Ford Taurus Wheel Interchange

2014 Ford Taurus Wheel Fitment Guide

Known OEM Fitment For 2014 Ford Taurus

The following specifications are the known fitment data available for the 2014 Ford Taurus on wheelinterchange.com. Equipment can vary by trim, package, market, and replacement-wheel history, so confirm the specifications for your specific vehicle before ordering.

Notice that the available wheel data lists an 18-inch rim, while the available tire data lists a 17-inch tire rim diameter. These values should not be assumed to describe one matched wheel-and-tire package. Verify the original tire size and wheel size on the driver-door certification label, the owner’s manual, the tire sidewall, or Ford service information. A tire must be mounted only on a wheel with the correct diameter and approved width range.

How To Use The Wheel Interchange Calculator

Use the calculator to compare a donor vehicle’s wheel and tire measurements with the measurements for your 2014 Ford Taurus. Select the donor vehicle in “Wheels from” and select the Taurus as the vehicle the wheels will be “Installed on.”

• Compare the donor wheel’s bolt pattern, center bore, diameter, width, and offset with the Taurus values shown above.
• Review the calculator’s comparison for inner clearance, outer position, and changes in wheel placement. A similar bolt pattern alone does not prove that a wheel fits.
• Use “Custom wheel size” when the donor wheel or an aftermarket wheel is not represented. Enter rim diameter, rim width, and offset as marked on the wheel.
• Use “Custom tire size” to enter the tire section width and aspect ratio. Confirm that the tire rim diameter matches the wheel diameter.
• When you change rim diameter, the calculator updates the tire diameter in the comparison. Recheck overall diameter, clearance, load rating, and speed rating after every change.

The calculator is a comparison aid, not a substitute for a physical test fit or Ford documentation. Brake-caliper clearance, suspension clearance, fender clearance, tire load capacity, and lug-seat compatibility must still be confirmed.

Fitment Checklist Before You Buy

• Confirm the vehicle identification number, trim, drivetrain, and original equipment wheel and tire information using Ford or vehicle documentation.
• Match the 5x114.3 bolt pattern and verify that the wheel has the correct number of stud holes and an appropriate lug-hole design.
• Check the 63.4 mm center-bore requirement. A smaller wheel bore will not fit over the hub. A larger bore may require correctly sized hub-centric rings if approved for the application.
• Compare offset and backspacing, not just diameter and width. The known values are ET39 and 5.54 inches of backspacing, but the correct replacement specification can vary by wheel package.
• Confirm the wheel’s load rating is adequate for the Taurus and its intended use.
• Verify tire size, load index, speed rating, rim diameter, and approved rim-width range from the tire manufacturer.
• Check clearance to brake calipers, struts, control arms, tie rods, wheel-well liners, and fenders through the full steering and suspension travel.
• Confirm the lug nuts match the wheel’s seat type, thread size, and thread engagement. The known thread size is M12 x 1.5, but the lug-seat style is not provided here.
• Do not rely on listings that claim a wheel fits every Ford or every 5x114.3 vehicle. Ask the seller for the exact diameter, width, offset, center bore, load rating, and lug-seat details.

Plus Sizing And Common Upgrades

Plus sizing changes the wheel diameter while maintaining a similar overall tire diameter by reducing tire sidewall height. It can change steering feel, ride comfort, road-noise levels, impact protection, speedometer accuracy, and the risk of wheel or tire damage.

The available data includes a 235 mm section width, 60 aspect ratio, and 17-inch tire rim diameter, as well as an 18-inch wheel specification. Because those entries are not a confirmed matched package, do not use them to calculate a replacement tire size without checking the vehicle label and tire manufacturer data.

When evaluating a larger or wider wheel, use the calculator’s custom fields and compare overall tire diameter, wheel position, and clearance. A larger wheel is not automatically an upgrade, and a wider tire can contact the vehicle even when the bolt pattern is correct.

Any replacement tire should meet or exceed the vehicle’s required load index and speed rating. Do not reduce sidewall height or load capacity solely to achieve a desired appearance.

Installation Tips

• Inspect used wheels for cracks, bends, corrosion around the bead seat, damaged lug holes, and evidence of repair before installation.
• Clean the hub mounting face and wheel mounting pad. Rust or debris between these surfaces can cause runout and vibration.
• Install tires only on wheels with matching bead-seat diameter and an approved tire-width range.
• Start every lug nut by hand to prevent cross-threading. Do not use an impact tool to force a lug nut onto damaged or mismatched threads.
• Tighten lug nuts in a star or crisscross pattern, then torque them to the Ford specification for the exact vehicle and wheel hardware. That torque value is not provided here, so confirm it in the owner’s manual or Ford service information.
• After installation, rotate the steering from lock to lock while stationary and inspect for contact. Then perform a slow-speed test in a safe area and listen for rubbing or vibration.
• Recheck lug-nut torque after the first short drive and again according to the wheel or vehicle manufacturer’s instructions.
• Check tire pressure using the driver-door label rather than the maximum pressure molded into the tire sidewall.

Tools And Helpful Supplies

Useful equipment includes a properly sized socket, a calibrated torque wrench, a jack and jack stands rated for the vehicle, wheel chocks, a tire-pressure gauge, and a hub and wheel cleaning brush. A tread-depth gauge and a straightedge or measuring tools can also help when checking used wheels and tires.

For a suitable torque wrench, see automotive torque wrenches on Amazon. For wheel and hub cleaning, see wheel and hub cleaning brush sets on Amazon.

Use jack stands on a solid, level surface and never work beneath a vehicle supported only by a jack. If a wheel requires spacers, adapters, or non-original fasteners, have the complete combination reviewed by a qualified wheel professional before driving.

FAQs

What is the bolt pattern for the 2014 Ford Taurus?
The known bolt pattern is 5x114.3. Confirm the wheel’s actual marking or manufacturer specification before purchase.

What is the center bore?
The known center bore is 63.4 mm. A wheel bore smaller than the vehicle hub will not fit. A larger bore may require a correctly sized hub-centric ring, subject to professional verification.

What lug thread size is listed?
The known thread size is M12 x 1.5. The correct lug nut also depends on the wheel’s seat type, which is not provided in the available data.

Can I install any 18-inch wheel?
No. Diameter is only one fitment measurement. You must also confirm bolt pattern, center bore, width, offset, load rating, brake clearance, lug-seat compatibility, and tire specifications.

Why does the data show an 18-inch wheel and a 17-inch tire rim diameter?
Those entries are inconsistent as a confirmed wheel-and-tire combination. They may represent different fitment records or packages. Check the door-jamb label, tire sidewall, owner’s manual, or Ford service information before ordering.

Can I use the calculator to check aftermarket wheels?
Yes. Select the vehicles for the donor and installed applications, then use the custom wheel size and custom tire size fields when needed. Recheck the result against the wheel manufacturer’s specifications and perform a physical clearance inspection.

What wheel offset should I buy?
The available data lists ET39 and 5.54 inches of backspacing, but the correct value may vary by wheel package and intended tire size. Use the calculator to compare offsets and verify brake, suspension, and fender clearance before purchase.

What lug torque should I use?
The required torque value is not provided here. Use the exact Ford specification for the vehicle and the installed wheel hardware from the owner’s manual or Ford service information. Do not guess.