2016 Ford Taurus Wheel Interchange

2016 Ford Taurus Wheel Fitment Guide

Known OEM Fitment For 2016 Ford Taurus

The following specifications are the known fitment data available for the 2016 Ford Taurus. Equipment can vary by trim, package, market, and wheel configuration, so confirm the original equipment label, owner’s manual, or Ford service information before ordering.

Important: the supplied data lists an 18-inch rim diameter while also listing a 17-inch tire rim diameter, which would correspond to a 235/60R17 tire size. These values should not be assumed to describe one complete wheel and tire package. Check the tire sidewall, driver-door placard, and OEM documentation to determine the correct configuration for your specific Taurus.

The 5x114.3 bolt pattern means five wheel studs are spaced on a 114.3 mm pitch circle. The center bore and thread size also need to match correctly. Do not force a wheel onto the vehicle or use improperly sized lug hardware.

How To Use The Wheel Interchange Calculator

Use the calculator on this page to compare a donor vehicle’s wheels with your 2016 Ford Taurus. Select the donor vehicle under “Wheels from” and select the Taurus under “Installed on.” The comparison helps identify differences in bolt pattern, center bore, wheel width, diameter, and offset when those specifications are available.

• Start with the donor vehicle and enter or select its wheel specifications.
• Set the 2016 Ford Taurus as the vehicle receiving the wheels.
• Review diameter, width, offset, bolt pattern, center bore, and clearance results.
• Use “Custom wheel size” to test a specific rim diameter, rim width, or offset.
• Use “Custom tire size” to compare section width and aspect ratio.
• When rim diameter changes, review the updated tire diameter shown by the calculator.

A calculator result is a screening tool, not a substitute for a physical test fit or OEM confirmation. It cannot verify brake caliper clearance, suspension clearance, fender clearance, tire load rating, or whether the correct lug nuts are included with an aftermarket wheel.

Fitment Checklist Before You Buy

• Confirm the Taurus trim, drivetrain, brake package, and original wheel size using the vehicle identification number, door placard, owner’s manual, or Ford parts information.
• Match the 5x114.3 bolt pattern exactly.
• Confirm that the wheel’s center bore is compatible with the 63.4 mm hub. A smaller bore will not fit. A larger bore may require correctly sized hub-centric rings where appropriate.
• Verify the wheel offset and backspacing. A change can move the wheel toward the strut, brake components, fender, or suspension.
• Confirm the wheel diameter and width provide adequate brake and suspension clearance.
• Choose tires with the correct load rating, speed rating, overall diameter, and approved rim-width range.
• Check that the tire does not contact the inner wheel well, strut, control arm, fender, or liner at full steering lock and full suspension compression.
• Confirm the lug nut seat type, thread size, shank length, and required torque for the specific wheels.
• Inspect used wheels for bends, cracks, corrosion around the bead seat, and damaged stud holes.
• After installation, verify tire pressure using the vehicle placard rather than relying on the maximum pressure molded into the tire sidewall.

Do not purchase solely because the bolt pattern matches. Correct fitment requires all critical dimensions and safe load capacity to be suitable for the vehicle.

Plus Sizing And Common Upgrades

Plus sizing changes the wheel diameter while maintaining a similar tire overall diameter by reducing the tire sidewall height. It can improve steering response and appearance, but it may reduce ride comfort and increase the risk of wheel or tire damage from potholes.

The supplied information does not establish a complete approved range of alternative wheel and tire sizes for every 2016 Ford Taurus trim. Use the calculator to model a custom wheel diameter, width, and offset, then compare the resulting tire diameter and clearance with the OEM specifications for your vehicle.

When changing tire size, keep the rolling diameter as close as practical to the vehicle’s confirmed original size. A substantial change can affect speedometer accuracy, clearance, gearing, traction-control operation, and advanced driver-assistance system behavior. Do not mix different tire sizes on the same axle unless specifically approved by the tire and vehicle manufacturers.

Installation Tips

• Clean the hub face and wheel mounting surface before installation. Rust or debris can prevent the wheel from seating flat.
• Install wheels by hand and start every lug nut by hand to avoid cross-threading.
• Use only lug nuts that match the wheel’s seat design and the vehicle’s M12 x 1.5 thread specification.
• Tighten lug nuts in a star or crisscross pattern, then torque them to the vehicle or wheel manufacturer’s specified value.
• Never use an impact wrench for final torque unless it is specifically controlled and followed by a calibrated torque wrench.
• Rotate the wheel by hand and inspect clearance before lowering the vehicle completely.
• Check clearance with the steering turned fully left and right. If safely possible, also check suspension compression clearance.
• After driving a short distance, recheck lug torque according to the wheel manufacturer’s instructions.
• Recheck tire pressure and monitor for vibration, rubbing, air loss, or steering pull.

Tools And Helpful Supplies

A calibrated torque wrench, correct socket, jack, jack stands, wheel chocks, and a reliable tire pressure gauge are useful for a safe wheel installation. Use jack stands on a solid, level surface and follow the vehicle’s approved lifting points. Never work under a vehicle supported only by a jack.

• Automotive torque wrench
• Digital tire pressure gauge

For professional or frequent work, a wheel balancer and tire mounting equipment may be appropriate. Tire mounting and balancing should be performed by a qualified shop when the required equipment or training is not available.

FAQs

What is the bolt pattern for the 2016 Ford Taurus?

The known bolt pattern is 5x114.3. The wheel must have five mounting holes on a 114.3 mm pitch circle.

What is the center bore of the 2016 Ford Taurus?

The supplied center bore specification is 63.4 mm. A replacement wheel with a smaller center bore will not fit over the hub. A larger bore may need a correctly sized hub-centric solution where appropriate.

What lug thread size is listed for this Taurus?

The known thread size is M12 x 1.5. Thread size alone does not confirm that a lug nut is correct because the lug seat and usable thread engagement must also match.

Can I install any 5x114.3 wheel on a 2016 Ford Taurus?

No. The bolt pattern is only one part of fitment. You must also verify center bore, offset, width, diameter, brake clearance, lug seat, tire size, load rating, and fender and suspension clearance.

Why does the supplied information show both 18-inch rims and a 17-inch tire rim diameter?

Those entries are inconsistent if they are intended to describe one wheel and tire package. A tire listed as 235/60R17 is designed for a 17-inch rim, while an 18-inch wheel requires a tire with an 18-inch rim diameter designation. Confirm the actual equipment on your vehicle and use the calculator to compare complete wheel and tire combinations.

How do I compare donor wheels with my Taurus?

Set the donor vehicle in “Wheels from” and the 2016 Ford Taurus in “Installed on.” Review the dimensional comparison, then test any proposed wheel using the custom wheel size and custom tire size fields. Confirm the donor specifications from the wheel manufacturer or vehicle documentation before buying.

Does changing wheel offset change clearance?

Yes. A different offset changes how far the wheel sits inward or outward. It can affect strut, brake, suspension, and fender clearance, so every offset change should be checked with the calculator and then physically verified.

Is the calculator a guarantee that a wheel will fit?

No. The calculator helps compare listed dimensions, but it cannot guarantee brake clearance, tire clearance, lug compatibility, load capacity, or safe operation. Confirm fitment with OEM sources, the wheel manufacturer, and a physical inspection before driving.