2016 Dodge Durango Wheel Interchange

2016 Dodge Durango Wheel Fitment and Interchange Guide

Known OEM Fitment For 2016 Dodge Durango

The values below reflect known original equipment specifications for at least one 2016 Dodge Durango configuration. Trims and option packages can vary. If a value is not listed for your exact VIN or trim, use the on-page calculator and confirm against your owner’s manual or Mopar service information before purchasing wheels or tires.

Important notes:

• Some Durango trims and brake packages may use different wheel diameters and offsets. Always verify your exact configuration.
• If you plan to install wheels from another vehicle, match bolt pattern, center bore, load rating, and offset/backspacing, then confirm clearance on your Durango.

How To Use The Wheel Interchange Calculator

The calculator on this page lets you compare a donor vehicle’s wheels to your 2016 Dodge Durango and test custom wheel and tire sizes before you buy.

• Step 1. In Installed on (your vehicle), select 2016 Dodge Durango. This is your baseline.
• Step 2. In Wheels from (donor vehicle), choose the vehicle you want to source wheels from. If you are evaluating a standalone wheel, you can use Custom wheel size.
• Step 3. Use Custom wheel size to set rim diameter, width, and offset for an aftermarket wheel you are considering.
• Step 4. Use Custom tire size to enter a tire section width and aspect ratio. When you change rim diameter, the comparison updates overall tire diameter so you can see the effect on ride height and gearing.
• Step 5. Review changes in tire diameter and wheel position. Increased width or lower offset pushes the wheel outward. Higher offset pulls it inward. Compare these changes to your available fender and suspension clearance.
• Step 6. If any value is unknown for your trim, use the calculator with your OEM size as the baseline and confirm final choices against OEM specifications and a physical test fit when possible.

Fitment Checklist Before You Buy

• Bolt pattern: Must be 5x127. 5x127 is the same as 5x5 in.
• Center bore: Your Durango hub is 71.6 mm. The wheel’s center bore must be 71.6 mm or larger. If larger, plan to use quality hub-centric rings to 71.6 mm. Never use a wheel with a smaller bore than the hub.
• Thread size and seat: M14 x 1.5. Verify lug nut seat profile that your wheels require (commonly 60-degree conical for many aftermarket wheels). Do not mix seat types.
• Offset and backspacing: OEM reference is 56 mm offset and 6.2 in backspacing on an 18x8. Keep inner clearance to struts and control arms, and outer clearance to fenders and liners. Use the calculator to visualize position changes.
• Brake clearance: Confirm spoke and barrel clearance over your specific brake package. Some trims have larger calipers and may require larger diameter or specific spoke designs.
• Tire diameter: OEM ~30.5 in with 265/60R18. Keep overall diameter change within about plus or minus 3 percent unless you plan to recalibrate the speedometer.
• Load and speed rating: Tires and wheels must meet or exceed the vehicle’s GAWR and OEM load index. Check the driver-door placard and owner’s manual.
• TPMS: Plan for compatible TPMS sensors and relearn procedure. Reuse OEM sensors when possible or install compatible replacements.
• Test fit: Always test fit a front and rear corner. Turn lock-to-lock and compress the suspension to check for rubbing before mounting tires or finalizing the purchase.

Plus Sizing And Common Upgrades

Plus sizing changes rim diameter and often tire width while keeping overall tire diameter close to stock. This maintains speedometer accuracy and helps avoid rubbing.

• Plus-one example method: Increase rim diameter by 1 in, reduce tire sidewall height to keep overall diameter near 30.5 in. Use the calculator to dial in a size that stays within about 3 percent of OEM diameter.
• Plus-two or more: Larger diameters can require higher offsets, different spoke profiles for brake clearance, and lower-profile tires. Ride quality may become firmer. Use the calculator to compare and then verify with a physical test fit.
• Wider wheels: If you increase rim width, the outer lip moves outward by half the width increase unless you also adjust offset. Use the calculator to balance inner and outer clearances.
• Winter setups: Narrower tires can improve winter traction. Keep overall diameter close to OEM and confirm brake clearance for smaller-diameter rims before buying.

Because 2016 Durango trims and packages vary, do not assume another size that fits one trim will fit yours. Confirm with the calculator and your OEM sources.

Installation Tips

• Inspect and prep: Clean hub faces and wheel mounting pads until bare metal. Remove rust scale that could cause runout. Do not grind or remove material from safety-critical surfaces.
• Dry threads: Install lug nuts on clean, dry studs unless the OEM service manual specifies otherwise. Do not lubricate threads or seats unless directed by the manufacturer.
• Hand start all lugs: Start every lug nut by hand to avoid cross-threading.
• Star pattern: Snug and torque in a crisscross pattern.
• Torque spec: Use the torque value in your owner’s manual or Mopar service information for the 2016 Durango. Recheck torque after 50 to 100 miles.
• Hub-centric rings: If your aftermarket wheels have a larger center bore than 71.6 mm, install proper rings so the wheel centers on the hub.
• TPMS: Transfer or install compatible sensors and complete the relearn procedure specified for your Durango.
• Final checks: Turn lock-to-lock, drive slowly over bumps, and listen for rubbing. If contact occurs, stop and correct before normal driving.

Tools And Helpful Supplies

• 1/2 inch drive torque wrench
• Thin wall lug nut socket set
• M14 x 1.5 lug nuts (verify seat type for your wheels)
• Hub-centric rings to 71.6 mm (size to match your wheel’s bore)

FAQs

• What is the bolt pattern for a 2016 Dodge Durango

  5x127 mm, which is the same as 5x5 in.

• What offset should I use with aftermarket wheels

  The known OEM reference is 56 mm on an 18x8. If you change width or offset, use the calculator to compare to OEM and verify inner and outer clearance on your vehicle. Trim and brake package differences may affect what fits.

• Do I need hub-centric rings

  If your wheel’s center bore is larger than 71.6 mm, use rings that reduce to 71.6 mm so the wheel centers on the hub. If the wheel bore is exactly 71.6 mm, no ring is needed. Never use a wheel with a bore smaller than 71.6 mm on this vehicle.

• Can I run 20 inch wheels on my 2016 Durango

  Some trims may support larger diameters, but fitment varies. Use the calculator to keep overall tire diameter close to OEM, confirm brake clearance, and verify offset and width. Check your owner’s manual and perform a physical test fit before buying.

• What tire diameter should I target to keep the speedometer close

  The OEM 265/60R18 is about 30.5 in in overall diameter. Aim to stay within about plus or minus 3 percent of that unless you plan to recalibrate. Use the calculator to evaluate sizes.

• What is the correct lug nut torque

  Refer to the 2016 Dodge Durango owner’s manual or Mopar service information for the exact torque specification. Use a calibrated torque wrench and recheck after 50 to 100 miles.

• Are 5x127 and 5x5 the same

  Yes. 5x127 mm is the metric equivalent of 5x5 in. You still must match center bore, offset, load rating, and ensure brake and fender clearance.

• Will aftermarket lug nuts fit my wheels

  They must match thread size M14 x 1.5 and the seat type that your wheel uses. Many aftermarket wheels require 60-degree conical seats, but verify with the wheel manufacturer.