2018 Dodge Durango Wheel Interchange

2018 Dodge Durango Wheel Fitment Guide

Known OEM Fitment For 2018 Dodge Durango

The values below reflect known factory specifications for at least one 2018 Dodge Durango configuration. Other trims or brake packages may use different wheel or tire sizes. If your Durango differs, confirm with your owner’s manual, the tire placard on the driver’s door jamb, and by using the on-page calculator to compare alternatives.

If a spec for your exact trim is not listed, do not guess. Check your OEM sources and then use the calculator to compare any new wheel or tire option against your baseline.

How To Use The Wheel Interchange Calculator

The calculator on this page helps you compare a potential setup against your 2018 Dodge Durango baseline. It shows inner clearance to suspension and outer poke relative to the fender, and it updates tire diameter when you change rim diameter.

• Installed on your vehicle: Enter your baseline 2018 Dodge Durango specs. Use the known OEM values above if they match your trim, or enter the values from your door jamb placard and factory wheel.
• Wheels from donor vehicle: Select a donor vehicle or use the Custom wheel size and Custom tire size fields to enter the wheel and tire you want to try.
• Adjust rim width and offset: Watch how inner clearance and outer poke change. Positive offset moves the wheel inward. Lower offset moves it outward.
• Change rim diameter: The tool will update tire diameter in the comparison. Keep overall tire diameter as close to stock as practical to help maintain speedometer accuracy and clearance. Choose a tire size that matches the new rim diameter while keeping overall diameter near OEM.
• Center bore and hardware: Ensure the new wheel bore is at least 71.6 mm. If larger, plan for hub-centric rings to 71.6 mm. Use M14 x 1.5 hardware that matches the wheel’s seat type.
• Validate physically: The calculator is a guide. Always test fit, check brake caliper clearance, and inspect inner fender and suspension clearances with the wheel fully turned and the suspension compressed.

Fitment Checklist Before You Buy

• Bolt pattern: Must be 5x127. Do not attempt to fit 5x114.3, 5x120, or other patterns.
• Center bore: Vehicle hub is 71.6 mm. Wheel bore must be equal or larger. Use hub-centric rings if the wheel bore is larger to prevent vibration.
• Offset and backspacing: Use the calculator to compare your target wheel to your baseline 18x8 ET56 and 6.2 in backspacing. Verify inner clearance to struts and control arms and outer poke relative to the fender.
• Brake clearance: Measure around calipers and spokes. Some trims may have larger brakes. Always test fit the front and rear.
• Tire sizing: Match load index and speed rating to meet or exceed OEM. Keep overall diameter close to stock to reduce speedometer and ABS calibration issues.
• TPMS: Plan to transfer sensors or purchase compatible replacements. Perform relearn as required.
• Lug hardware: Thread size is M14 x 1.5. Match seat type and length to the wheel manufacturer’s instructions.
• Spacers or adapters: If used, they must be high quality and hub-centric. Ensure adequate stud engagement and verify clearances. Check local regulations.
• Return policy: Confirm the seller’s return policy in case your test fit shows interference.

Plus Sizing And Common Upgrades

Owners sometimes consider larger diameter wheels for appearance or handling, or different widths for tire choices. The 2018 Dodge Durango was offered in multiple trims and brake packages, so sizes may vary by trim. If you are considering an upgrade, do the following:

• Use the calculator to model a larger rim diameter and select a tire size that keeps overall diameter close to stock.
• Compare inner clearance and outer poke against the 18x8 ET56 baseline. Verify at full steering lock and over bumps.
• If downsizing for winter, confirm brake clearance first. Some brake packages may not clear smaller diameters.
• Check tire manufacturer approved rim width range for any tire you select to ensure it is safe on your chosen wheel width.

Installation Tips

• Preparation: Park on level ground, secure the vehicle, and use jack stands at proper points. Loosen lugs slightly before lifting.
• Clean mating surfaces: Remove rust and debris from the hub face. A clean, flat hub helps prevent vibration.
• Test fit first: Mount one wheel without a tire if possible to check caliper and spoke clearance, then with tire installed to confirm inner and outer clearances.
• Hub-centric rings: If using rings, ensure they seat fully on the hub and in the wheel bore.
• Lug nuts: Hand-thread all M14 x 1.5 lugs to avoid cross-threading. Tighten in a star pattern.
• Final torque: Use a calibrated torque wrench and the torque spec from your owner’s manual. Re-torque after 50 to 100 miles.
• TPMS: Install compatible sensors and perform the relearn procedure per Dodge service information.

Tools And Helpful Supplies

• 1/2 inch drive torque wrench
• M14 x 1.5 lug nuts
• 71.6 mm hub-centric rings
• 3 ton jack stands

FAQs

• What is the bolt pattern on the 2018 Dodge Durango?

  5x127. This is the same as 5x5 inch in imperial units.

• What center bore do I need?

  71.6 mm. Wheels with a larger bore can be used with hub-centric rings sized to 71.6 mm.

• What lug nut thread size does it use?

  M14 x 1.5. Match the lug seat type to the wheel design.

• What is a known stock wheel and tire size for 2018 Durango?

  18x8 ET56 wheel with 6.2 in backspacing and 265/60R18 tires on at least one factory configuration. Other trims may differ.

• Will wheels from another vehicle fit my Durango?

  Possibly. Use the calculator to compare the donor wheel and tire to your Durango’s baseline. Ensure 5x127 bolt pattern, center bore equal or larger with rings to 71.6 mm, appropriate offset and backspacing, brake clearance, correct hardware, and TPMS compatibility. Always test fit.

• Do I need hub-centric rings with aftermarket wheels?

  If the wheel’s center bore is larger than 71.6 mm, use rings to center the wheel on the hub. If the bore is exactly 71.6 mm, rings are not needed.

• What offset range will fit?

  It depends on wheel width, tire size, and your trim’s brake and fender clearances. Use the calculator to compare inner and outer clearances, then verify with a physical test fit.

• Can I upsize to a larger wheel diameter?

  Many owners do, but sizes vary by trim and brake package. Use the calculator to choose a tire that keeps overall diameter close to stock, confirm brake clearance, and verify with a test fit.

Use this guide with the on-page calculator to plan a safe fitment for your 2018 Dodge Durango. When in doubt, consult OEM documentation or a professional installer.