2009 Ford Focus Wheel Interchange
Known OEM Fitment For 2009 Ford Focus
The following specifications are the known reference values for the 2009 Ford Focus information on this page. Fitment can vary by trim, market, brake package, and wheel design, so confirm the vehicle identification information and compare the replacement wheel with the original before purchase.
| Specification |
Known value |
| Bolt pattern |
4x108 |
| Center bore |
63.4 mm |
| Thread size |
M12 x 1.5 |
| Rim diameter |
15 inches |
| Rim width |
6.0 inches |
| Wheel offset |
ET53, or 53 mm |
| Backspacing |
5.09 inches |
| Reference tire size |
195/60R15 |
| Tire section width |
195 mm |
| Tire aspect ratio |
60 percent |
These values describe the supplied OEM reference configuration. They do not by themselves confirm that every 4x108 wheel will clear the brakes, suspension, fenders, or bodywork. Wheel spoke shape, barrel design, offset, width, and tire choice can all affect actual fit.
How To Use The Wheel Interchange Calculator
Use the calculator to compare a potential donor wheel with the wheel configuration installed on your 2009 Ford Focus. Enter the donor vehicle or donor wheel details in “Wheels from” and the Focus details in “Installed on.” The comparison is useful for identifying differences in bolt pattern, center bore, diameter, width, and offset, but it is not a substitute for a physical test fit or OEM confirmation.
When the donor vehicle is not listed or you are evaluating a custom setup, select the custom wheel size fields. Enter the rim diameter, rim width, and wheel offset, then enter the tire section width and aspect ratio. Changing the rim diameter updates the tire diameter in the comparison, so review the resulting diameter before deciding whether the tire is appropriate.
Use the known values above as the starting point for the installed vehicle. If your trim, market, or original wheel label differs, verify the specification from the owner’s manual, the vehicle certification information, the wheel markings, or a Ford parts source before relying on the comparison.
Fitment Checklist Before You Buy
Confirm the replacement wheel has the correct 4x108 bolt pattern and that its mounting holes are designed for the correct M12 x 1.5 fasteners. The wheel must also have a 63.4 mm center bore or use a properly selected hub-centric solution when appropriate. Do not use rings to correct an undersized center bore.
Compare the proposed diameter, width, and offset with the known 15 x 6.0 wheel at ET53. A change in offset or width changes the wheel’s position relative to the strut, suspension, fender, and inner bodywork. Confirm spoke clearance to the brake assembly, inner clearance at full steering lock, and clearance under suspension compression.
Verify the tire’s load rating, speed rating, overall diameter, approved rim-width range, and inflation requirements. The 195/60R15 reference size should not be treated as permission to install another tire size without checking the vehicle and tire manufacturer guidance.
Inspect used wheels for cracks, bends, corrosion around the bead seat, damaged mounting faces, and stretched or damaged bolt holes. Ask the seller for exact wheel markings rather than relying only on a vehicle make and model description.
Plus Sizing And Common Upgrades
Plus sizing means using a larger wheel diameter with a lower-profile tire while attempting to maintain a similar overall tire diameter. It can change ride comfort, steering response, wheel protection, ground clearance, speedometer behavior, and the risk of contact with suspension or body components.
The calculator can compare custom rim diameter, rim width, offset, tire section width, and tire aspect ratio. Treat its diameter comparison as a screening tool. It does not verify brake clearance, spoke clearance, tire load capacity, fender clearance, or whether a tire is approved for a particular wheel width.
Before selecting an upgrade, obtain the exact wheel specifications and tire manufacturer data. Confirm that the final assembly remains clear at full left and right steering lock and through the vehicle’s available suspension travel. If the tire or wheel extends beyond the body, local regulations and inspection requirements may also apply.
Installation Tips
Clean the hub face and wheel mounting surface before installation. Remove rust, dirt, and paint buildup that could prevent the wheel from sitting flat. Never install a wheel with a damaged or contaminated mounting face.
Use only compatible wheel fasteners with the correct seat type for the wheel. Thread size alone does not confirm that a lug nut or bolt has the correct seat. Do not force a fastener or use impact tools to start it, because cross-threading can damage the hub or fastener.
Install fasteners by hand first, then tighten them in a star or crisscross sequence. Apply the vehicle manufacturer’s specified final torque with a calibrated torque wrench. The required torque is not provided here, so check the owner’s manual or an authorized Ford service source instead of guessing.
After installation, check for clearance with the steering at both full-lock positions. Recheck fastener torque after the initial driving period specified by the wheel or vehicle manufacturer, and inspect for vibration, rubbing, loss of air pressure, or other changes before continued use.
Tools And Helpful Supplies
Useful equipment includes a calibrated torque wrench, suitable socket, wheel chocks, a safe jack, properly rated jack stands, and a tire pressure gauge. A straightedge or clearance gauge can help with basic checks, but it cannot replace a complete loaded suspension and steering inspection.
For a torque wrench search, see automotive torque wrenches on Amazon. For routine pressure checks, see digital tire pressure gauges on Amazon.
Use jack stands on a solid, level surface and follow the jack and stand manufacturer’s instructions. Never work under a vehicle supported only by a jack.
FAQs
What is the bolt pattern for the 2009 Ford Focus?
The known reference bolt pattern is 4x108. Confirm the pattern for the specific vehicle and replacement wheel before purchase.
What center bore is listed for this 2009 Ford Focus fitment?
The known center bore is 63.4 mm. A wheel with a smaller bore will not fit over the hub. A larger bore may require an appropriate centering solution if approved for the wheel and vehicle.
What is the reference factory wheel and tire size?
The supplied reference configuration is a 15 x 6.0 wheel at ET53 with a 195/60R15 tire. This is a reference value and may not represent every trim or market configuration.
Can any 4x108 wheel be installed?
No. The bolt pattern is only one part of fitment. You must also verify center bore, offset, width, fastener seat and thread compatibility, brake and spoke clearance, tire specifications, and body clearance.
Can I use the calculator to choose a larger wheel?
Yes, the calculator lets you compare custom rim diameter, width, offset, tire section width, and aspect ratio. It updates tire diameter when the rim diameter changes. You must still confirm physical clearance, load and speed ratings, approved rim width, and OEM or tire manufacturer guidance.
Does the listed thread size tell me which lug nuts to buy?
The known thread size is M12 x 1.5, but thread size alone is not enough. The fastener must also have the correct seat style, length or engagement, and strength for the specific wheel. Confirm these details with the wheel manufacturer or an OEM service source.
How can I confirm whether a donor wheel really fits?
Record the donor wheel’s bolt pattern, center bore, diameter, width, offset, and fastener requirements. Enter those values in the calculator, compare them with the installed Focus values, and then verify the exact specifications using wheel markings, the donor vehicle documentation, and a physical clearance check.
