2013 Ford Transit Connect Wheel Fitment and Interchange Guide
Known OEM Fitment For 2013 Ford Transit Connect
The following wheel and tire specifications are the known OEM fitment values provided for the 2013 Ford Transit Connect. Confirm the exact equipment on your vehicle using the door-jamb label, owner documentation, the original wheel markings, and the on-page wheel interchange calculator before purchasing.
| Specification |
Known value |
| Bolt pattern |
5x108 |
| Center bore |
63.4 mm |
| Thread size |
M12 x 1.5 |
| Rim diameter |
15 inches |
| Rim width |
6.0 inches |
| Wheel offset |
ET53, or 53 mm |
| Backspacing |
5.09 inches |
| Tire section width |
205 mm |
| Tire aspect ratio |
65 percent |
| Tire rim diameter |
R15 |
These specifications describe the provided reference fitment and should not be treated as proof that every wheel from another vehicle will fit. Wheel design, brake clearance, load rating, tire clearance, and trim-level equipment can affect compatibility.
How To Use The Wheel Interchange Calculator
Use the calculator to compare wheels from a donor vehicle with the wheels installed on your 2013 Ford Transit Connect. Enter the donor vehicle information in the “Wheels from” fields and enter the Transit Connect information in the “Installed on” fields.
- Compare the donor wheel diameter, width, and offset with the known Transit Connect values.
- Check the bolt pattern, center bore, and thread requirements separately. Similar-looking wheels are not automatically interchangeable.
- Use the “Custom wheel size” controls to test a proposed rim diameter, rim width, and offset.
- Use the “Custom tire size” controls to compare tire section width and aspect ratio.
- Remember that changing rim diameter updates the tire diameter in the comparison.
- Use the calculator as a screening tool, then verify physical clearance and vehicle-specific requirements before installation.
A calculator comparison cannot confirm brake-caliper clearance, wheel load rating, tire load index, steering and suspension clearance, or whether a wheel requires different fasteners. Those checks must be completed before driving.
Fitment Checklist Before You Buy
Use this checklist when evaluating replacement, used, aftermarket, or donor wheels for a 2013 Ford Transit Connect:
- Confirm the wheel uses the 5x108 bolt pattern.
- Confirm the center bore is compatible with the vehicle hub. A smaller bore will not fit over the hub. A larger bore may require correctly specified hub-centric rings if appropriate for the wheel application.
- Check that the wheel uses the correct M12 x 1.5 fastener specification and that the seat type matches the wheel. Do not assume the original fasteners are suitable for a different wheel.
- Compare the proposed rim diameter, width, and offset with the known 15 x 6.0 ET53 reference.
- Check the wheel for its load rating and confirm that it is appropriate for the vehicle and intended cargo.
- Inspect used wheels for cracks, bends, corrosion around the bead seat, damaged bolt holes, and previous repairs.
- Verify tire size, load index, speed rating, condition, and age. The known reference tire is 205/65R15.
- Test for clearance at the brake caliper, strut or suspension components, inner wheel well, fender, and steering lock before road use.
- Confirm that the tire does not contact the vehicle during compression, turning, or loaded operation.
OEM wheels, tire placards, and the vehicle owner information are the best sources for confirming equipment-specific requirements. If any measurement is different from the known values on this page, use the vehicle-specific information and have the wheel checked by a qualified technician.
Plus Sizing And Common Upgrades
Plus sizing normally means installing a larger-diameter wheel with a lower-aspect-ratio tire while attempting to maintain a similar overall tire diameter. The calculator can help compare custom wheel and tire dimensions, but it does not approve a particular upgrade.
When considering a larger or wider wheel, evaluate the change in wheel width and offset, tire section width, sidewall height, overall diameter, steering clearance, suspension clearance, fender clearance, ride quality, speedometer behavior, and load capacity. A larger wheel may also be heavier or more vulnerable to impact damage.
Do not select an upgraded size solely because it shares the 5x108 bolt pattern. The complete fitment must also account for center bore, fastener compatibility, brake clearance, wheel load rating, and tire specifications. Exact optional or upgraded sizes for this vehicle are not listed here because they were not provided. Confirm any proposed size through Ford documentation, the tire placard, wheel manufacturer data, and a physical test fit.
Installation Tips
- Clean the hub face and wheel mounting surface before installation. Remove rust and debris without removing structural material.
- Check that the wheel seats fully against the hub and that no debris prevents a flush mounting surface.
- Use only fasteners with the correct M12 x 1.5 thread, seat design, length, and strength for the selected wheel.
- Start all fasteners by hand to avoid cross-threading.
- Tighten fasteners in a star or crisscross sequence, then torque them with a calibrated torque wrench to the vehicle or wheel manufacturer's specification. The correct torque value was not provided here, so do not use a guessed value.
- After installation, rotate each wheel by hand and inspect for obvious interference. Lower the vehicle and recheck clearance with the steering turned in both directions.
- Recheck fastener torque after the first short drive and again according to the wheel or vehicle manufacturer's instructions.
- Stop driving if you feel vibration, rubbing, pulling, or loosening, or if a warning sign appears after installation.
Tools And Helpful Supplies
Useful equipment for a careful wheel installation may include a calibrated torque wrench, correctly sized socket, jack and approved jack stands, wheel chocks, a tire pressure gauge, a tread-depth gauge, and a hub or wheel cleaning brush. A wheel fitment gauge or careful measurement can help identify interference, but it does not replace manufacturer specifications or a professional inspection.
Shop automotive torque wrenches on Amazon
Shop automotive wheel chocks on Amazon
FAQs
What is the bolt pattern for a 2013 Ford Transit Connect?
The known bolt pattern is 5x108, meaning five fastener positions on a 108 mm pitch circle diameter. Bolt pattern alone does not confirm complete wheel compatibility.
What is the center bore?
The known center bore is 63.4 mm. Confirm the donor wheel's bore and check whether any hub-centric ring is correctly specified for the wheel and vehicle.
What wheel size is listed for the reference fitment?
The provided reference fitment is a 15-inch diameter wheel that is 6.0 inches wide, with an ET53 offset and 5.09-inch backspacing.
What tire size is listed for the 2013 Transit Connect?
The known reference tire size is 205/65R15. Confirm the tire placard and vehicle documentation for the exact vehicle and equipment configuration.
Can any 5x108 wheel fit this vehicle?
No. The bolt pattern is only one part of fitment. Center bore, offset, width, brake clearance, fastener seat and thread requirements, wheel load rating, tire specifications, and body or suspension clearance must also be checked.
Can I use a wheel with a different offset?
A different offset changes the wheel's position relative to the hub, suspension, and fender. Use the calculator to compare custom offset and width, then verify clearance and load requirements with the wheel manufacturer or a qualified technician. No alternate offset is approved by the information provided here.
What thread size is listed?
The known thread size is M12 x 1.5. The fastener seat type and correct tightening torque were not provided, so confirm both before installing replacement wheels.
Does the calculator guarantee that a donor wheel will fit?
No. It compares the entered dimensions and updates tire diameter when rim diameter changes. Final fitment still requires verification of physical clearance, fastener compatibility, load rating, tire requirements, and vehicle-specific OEM information.