2019 Ford Transit Connect Wheel Interchange

2019 Ford Transit Connect Wheel Fitment

Known OEM Fitment For 2019 Ford Transit Connect

The following specifications are the known fitment values provided for the 2019 Ford Transit Connect. Equipment can vary by trim, package, market, and wheel or tire configuration, so confirm the markings on your vehicle and the applicable Ford service information before purchasing parts.

The supplied rim diameter and tire rim diameter do not match: the wheel data lists 17 inches, while the tire data lists a 16-inch rim diameter. Do not treat 215/55R16 as a confirmed match for a 17-inch wheel. Verify the tire size printed on the vehicle, the tire sidewall, and the certification label or owner documentation. A tire must match the wheel diameter exactly.

How To Use The Wheel Interchange Calculator

Use the on-page calculator to compare wheels from a donor vehicle with wheels installed on your 2019 Ford Transit Connect. Enter the donor vehicle and review its bolt pattern, center bore, wheel width, diameter, and offset against the known Transit Connect values above.

Use the custom wheel size fields when you are considering an aftermarket or nonstandard wheel. Adjust rim diameter, rim width, and offset, then check the resulting position for clearance inside the wheel well and around the suspension, steering, brakes, and fender.

You can also enter a custom tire section width and aspect ratio. Changing rim diameter updates the tire diameter in the comparison, but the calculator is not a substitute for a physical clearance check, load-rating review, tire-pressure guidance, or an OEM fitment confirmation.

When a specification is missing or varies by trim, use the calculator to compare the actual part numbers or measurements you have. Confirm the final result with Ford documentation, the wheel manufacturer, and the tire manufacturer before ordering.

Fitment Checklist Before You Buy

Confirm that the wheel uses the 5x108 bolt pattern and has a center bore of at least 63.4 mm. A larger center bore may require correctly sized hub-centric rings, while a smaller center bore will not fit over the vehicle hub. Confirm the wheel manufacturer’s hub-ring and lug-nut requirements.

Check the proposed wheel diameter, width, and offset against the calculator and the vehicle. The provided reference wheel data is 17 x 7.0 inches with ET50 offset and 5.47-inch backspacing, but this should not be assumed to cover every 2019 Transit Connect trim or package.

Verify brake-caliper clearance, spoke clearance, inner-barrel clearance, suspension clearance, and fender clearance. Also check that the replacement wheel supports the vehicle’s required load rating and uses the correct lug-seat design.

Confirm the tire size, load index, speed rating, inflation requirements, and overall diameter. Do not install a tire on a wheel with a different bead-seat diameter. The 16-inch tire value supplied here must be reconciled with the supplied 17-inch rim value before purchase.

Plus Sizing And Common Upgrades

Plus sizing generally means fitting a larger-diameter wheel with a lower-profile tire while keeping the overall tire diameter close to the original. It can change steering feel, ride comfort, road-noise levels, curb protection, tire cost, and clearance. It may also affect the accuracy of vehicle systems that rely on wheel-speed or tire-diameter information.

Do not select a plus-size combination from rim diameter alone. Use the calculator to compare the complete wheel and tire combination, then verify the tire manufacturer’s approved rim-width range and the vehicle’s required load capacity. A wheel that fits the bolt pattern can still be unsafe or unsuitable because of offset, center bore, brake clearance, or load rating.

For any upgrade, preserve adequate clearance at full steering lock and through suspension travel. If the vehicle has tire-pressure monitoring sensors, confirm sensor compatibility and follow the correct relearn procedure after installation.

Installation Tips

Inspect used wheels for cracks, bends, corrosion, repaired damage, and damaged lug holes. Clean the hub mounting face and wheel mating surface so the wheel seats fully and evenly. Never use spacers, adapters, or hub rings to compensate for an incorrect bolt pattern.

Install the correct lug hardware for the wheel’s seat type and thread specification. The provided vehicle thread size is M12 x 1.5, but the wheel manufacturer’s hardware requirements must also be confirmed. Do not force incompatible lug nuts onto the studs.

Hand-start every lug nut, lower the vehicle enough to prevent the wheel from turning, and tighten in a crisscross sequence. Use the vehicle manufacturer’s specified torque value with a calibrated torque wrench. Because that torque value was not provided here, obtain it from Ford service information or the owner documentation rather than guessing.

After installation, check for rubbing during steering lock-to-lock movement and inspect clearance after a cautious test drive. Recheck lug torque after the manufacturer’s recommended distance or procedure, and monitor tire pressure using the vehicle’s specified cold-pressure information.

Tools And Helpful Supplies

Useful equipment includes a calibrated torque wrench, suitable socket, jack and properly rated jack stands, wheel chocks, a tire-pressure gauge, and a tread or clearance inspection tool. Use the vehicle’s approved lift points and never work under a vehicle supported only by a jack.

A torque wrench can help apply the specified wheel-fastener torque consistently: view automotive torque wrenches on Amazon.

If the replacement wheel has a larger center bore, correctly sized hub-centric rings may help center the wheel, but they do not correct a bolt-pattern, offset, load-rating, or brake-clearance problem. Confirm the exact inner and outer diameters before ordering.

FAQs

What is the bolt pattern for the 2019 Ford Transit Connect?

The provided bolt pattern is 5x108. Confirm the wheel manufacturer’s specifications before purchase, especially for used or aftermarket wheels.

What is the center bore?

The provided center bore is 63.4 mm. A wheel with a smaller center bore will not fit over the hub. A larger bore may require an accurately sized hub-centric ring if recommended by the wheel manufacturer.

What lug thread size is provided for this vehicle?

The provided thread size is M12 x 1.5. The correct lug-nut seat and overall hardware design still depend on the specific wheel. Confirm compatibility rather than relying on thread size alone.

What wheel size is listed?

The provided wheel data lists a 17-inch diameter, 7.0-inch width, ET50 offset, and 5.47-inch backspacing. These values may not represent every trim or configuration, so compare the actual vehicle and wheel information in the calculator and OEM sources.

Is 215/55R16 confirmed for a 2019 Ford Transit Connect?

No. The supplied tire fields list 215 mm section width, a 55 percent aspect ratio, and a 16-inch rim diameter, but the supplied wheel diameter is 17 inches. Because the diameters conflict, treat this tire size as unconfirmed until the vehicle label, tire sidewall, and Ford documentation establish the correct configuration.

Will any 5x108 wheel fit?

No. Bolt pattern is only one part of fitment. Center bore, offset, width, backspacing, brake clearance, lug-seat design, load rating, and tire compatibility must also be correct.

How can I compare a donor vehicle’s wheels?

Enter the donor vehicle under “Wheels from” and the 2019 Ford Transit Connect under “Installed on.” Compare all available dimensions, then use the custom wheel and tire fields for parts that are not listed. Physically verify clearance and confirm the final specifications with OEM and manufacturer sources.

Do I need to recheck the wheels after installation?

Yes. Check for rubbing, uneven seating, vibration, and tire-pressure-monitoring warnings. Recheck lug torque according to Ford’s service procedure or owner documentation, and stop driving if a wheel contacts the vehicle or develops unusual vibration.