2019 Ford F-350 Wheel Interchange

2019 Ford F-350 Wheel Interchange and Fitment Guide

Use this guide to compare wheels and tires for a 2019 Ford F-350. The confirmed specifications below are limited to the available OEM fitment data. Rim diameter, rim width, offset, backspacing, and tire-size information can vary by configuration and are not listed here as confirmed values. Always verify the exact requirement for your truck using the door-jamb certification label, owner’s manual, VIN-based Ford parts information, or an authorized Ford dealer.

Known OEM Fitment For 2019 Ford F-350

A wheel with the correct 8x170 bolt pattern is not automatically compatible. The wheel must also clear the brakes and suspension, use a suitable center bore and lug-seat design, provide adequate load capacity, and maintain safe tire clearance. Confirm whether your truck has a configuration-specific wheel arrangement before purchasing.

How To Use The Wheel Interchange Calculator

The calculator compares Wheels from a donor vehicle with Installed on your 2019 Ford F-350. Enter the donor vehicle and the target truck carefully, then review the differences in wheel and tire dimensions.

1. Set the installed vehicle to the 2019 Ford F-350.
2. Choose the donor vehicle whose wheels or tires you want to evaluate.
3. Compare bolt pattern, center bore, wheel width, diameter, offset, and tire dimensions where data is available.
4. Use the Custom wheel size controls to enter a proposed rim diameter, rim width, and offset when the wheel is aftermarket or the donor data is incomplete.
5. Use the Custom tire size controls to enter section width and aspect ratio.
6. Review the calculated diameter and clearance changes. Changing rim diameter updates the tire diameter in the comparison, so recheck the complete tire and wheel combination after every adjustment.

The calculator is a comparison aid, not a substitute for physical inspection or OEM confirmation. If a value is missing, do not treat the blank or unknown value as approval. Confirm the measurement from the wheel marking, tire sidewall, Ford documentation, or a qualified wheel and tire professional.

Fitment Checklist Before You Buy

• Confirm the wheel uses the 8x170 bolt pattern.
• Confirm the wheel’s center bore is compatible with the 124.9 mm hub specification. A smaller bore will not fit over the hub. A larger bore may require correctly sized hub-centric rings where appropriate.
• Verify the wheel’s lug-seat type, stud engagement, and compatibility with M14 x 1.5 hardware. Never assume the original lug nuts fit an aftermarket wheel.
• Check wheel diameter, width, and offset against the calculator and the vehicle’s verified OEM specifications.
• Inspect inner clearance to the brake caliper, suspension, steering components, and hub assembly.
• Inspect outer clearance to the fender, mud flap, and bodywork through the full steering and suspension range.
• Choose tires with an adequate load index and speed rating for the truck’s actual use. Do not reduce load capacity for appearance or convenience.
• Confirm the tire’s approved rim-width range and ensure the tire diameter is appropriate for the vehicle and drivetrain.
• Check spare-tire compatibility, especially if the replacement wheel and tire differ from the verified original equipment.
• Ask the seller for exact wheel markings, offset, center bore, load rating, lug-seat information, and return terms before ordering.

Plus Sizing And Common Upgrades

Plus sizing generally means using a larger wheel diameter with a lower-profile tire to keep the overall tire diameter near the original. Because the verified OEM rim diameter and tire dimensions for this page are unknown, a specific plus-size recommendation would be unreliable. Use the calculator to compare candidate wheel and tire combinations, then verify the result against the original tire size and the manufacturer’s fitment requirements.

When changing wheel diameter, do not evaluate the wheel alone. A different tire diameter can affect speedometer accuracy, ground clearance, drivetrain behavior, fender clearance, and the operation of systems that use wheel-speed data. A wider tire can also change steering clearance and road-load requirements.

For work trucks, towing, hauling, or frequent off-road use, prioritize the required load capacity, sidewall durability, brake clearance, and safe clearance over visual changes. Any upgrade should preserve adequate capacity for the truck, occupants, cargo, and trailer-related demands.

Installation Tips

• Inspect every replacement wheel for cracks, bends, corrosion, damaged mounting seats, and missing specifications before installation.
• Clean the hub and wheel mounting surfaces. Remove rust and debris without removing metal or applying lubricant between the mounting faces.
• Install only compatible lug nuts with the correct thread and seat. Do not force mismatched hardware.
• Hand-start each lug nut to prevent cross-threading, then tighten in a star or crisscross pattern.
• Use a calibrated torque wrench and the torque specification stated by Ford or the wheel manufacturer. The required torque is not provided here and should not be guessed.
• Check tire pressure using the vehicle’s door-jamb label as the starting reference, then follow the tire and load recommendations for the actual setup.
• After installation, verify clearance at full steering lock and inspect for contact while the suspension is loaded and unloaded where practical.
• Recheck lug torque after the first short drive and again according to the wheel manufacturer’s instructions. Stop immediately if vibration, rubbing, loose hardware, or loss of pressure occurs.

Tools And Helpful Supplies

A basic installation may require a floor jack and properly rated jack stands, wheel chocks, a breaker bar, a calibrated torque wrench, a socket that matches the lug nuts, a tire-pressure gauge, and a tread-depth gauge. Use lifting points and support procedures specified for the truck. Never rely on a jack alone while working underneath or beside the vehicle.

Useful inspection supplies include a straightedge and ruler for checking wheel dimensions, a digital caliper for non-safety-critical measurements, a flashlight, and a hub-cleaning brush. For torque and wheel-hardware options, see automotive torque wrenches and wheel lug-nut tools on Amazon.

For a proposed wheel change, a wheel backspacing and offset measuring tool on Amazon can help document the existing setup. Measurements should still be checked against verified wheel specifications and physical clearance.

FAQs

What is the bolt pattern for a 2019 Ford F-350?

The known bolt pattern is 8x170. This means eight studs arranged on a 170 mm pitch circle diameter. Verify the vehicle configuration and wheel specifications before ordering.

What center bore does the 2019 Ford F-350 use?

The known center bore specification is 124.9 mm. The replacement wheel must clear the hub. A larger wheel bore may need a properly selected hub-centric ring, while a smaller bore will not fit over the hub.

What lug thread size is listed for the 2019 Ford F-350?

The known thread size is M14 x 1.5. Thread size alone does not identify the correct lug nut. The lug-seat shape, seat angle, washer design where applicable, and required engagement must also match.

What are the original wheel diameter, width, and offset?

Those values are unknown in the supplied fitment data and may vary by trim or configuration. Check the wheel’s stamped or cast markings, the tire and door-jamb labels, Ford’s VIN-specific parts information, or an authorized Ford dealer. You can also enter verified custom wheel dimensions in the calculator.

Can I install any 8x170 wheel on a 2019 Ford F-350?

No. The bolt pattern is only one part of fitment. Check center bore, lug-seat compatibility, wheel load rating, diameter, width, offset, brake clearance, suspension clearance, and fender clearance. The tire must also have the correct load capacity and approved rim-width range.

How do I compare a donor vehicle’s wheels with my truck?

Set the donor vehicle in the calculator’s Wheels from field and set the 2019 Ford F-350 in Installed on. Review every available dimension, then use the custom wheel and tire fields for verified measurements that are not listed. Treat unknown values as items requiring confirmation, not as a compatibility approval.

Does changing wheel diameter change tire diameter?

In the calculator, changing rim diameter updates the tire diameter in the comparison. The tire’s full size must still be selected or entered correctly. A larger wheel does not automatically preserve the original overall diameter unless the replacement tire has a suitable sidewall height.

Should I use wheel spacers to correct fitment?

Do not use spacers as a shortcut for unknown or incorrect fitment. They change offset and can affect bearing loads, stud engagement, clearance, and legal or manufacturer requirements. If a spacer is being considered, obtain vehicle-specific guidance from the spacer manufacturer and a qualified technician.