2020 Ford F-350 Wheel Interchange

2020 Ford F-350 Wheel Fitment Guide

Known OEM Fitment For 2020 Ford F-350

The verified fitment information available for the 2020 Ford F-350 is listed below. Factory wheel and tire specifications can vary by trim, drivetrain, axle configuration, payload rating, and original equipment package. Do not treat an unknown value as a recommendation.

These known measurements help identify the basic hub and stud pattern, but they do not confirm complete wheel clearance or tire compatibility. Confirm the exact original equipment specifications using the vehicle door-jamb label, owner's manual, Ford service information, or the wheel and tire markings on your truck.

How To Use The Wheel Interchange Calculator

Use the calculator to compare wheels from a donor vehicle with the wheels installed on your 2020 Ford F-350. Enter the donor vehicle information in “Wheels from” and enter your truck in “Installed on.” Compare the bolt pattern, center bore, wheel dimensions, offset, and tire dimensions before considering a purchase.

If the donor information does not match a listed vehicle, use “Custom wheel size” to enter the rim diameter, rim width, and offset. Use “Custom tire size” to enter the tire section width and aspect ratio. Changing the rim diameter updates the tire diameter shown in the comparison, which helps you review overall size changes.

The calculator is a comparison aid, not a substitute for a physical test fit or manufacturer confirmation. A result should be treated as incomplete when any required vehicle, wheel, or tire specification is unknown.

Fitment Checklist Before You Buy

Before ordering wheels or tires, verify every item that affects safe installation and clearance:

• Confirm the 8x170 bolt pattern and M14 x 1.5 thread size.
• Confirm that the wheel center bore is compatible with the supplied 124.9 mm vehicle center bore. A smaller wheel bore will not fit over the hub.
• Confirm the exact OEM rim diameter, rim width, offset, backspacing, and tire size for your specific trim and axle configuration.
• Check brake caliper, suspension, steering, hub, and inner-fender clearance with the actual wheel design, not only its advertised dimensions.
• Verify the wheel and tire load capacity against the requirements shown by Ford and on the vehicle certification label.
• Confirm that the lug nuts properly match the replacement wheel's seat type and thread requirements. Do not assume the original lug nuts are suitable for an aftermarket wheel.
• Check that the tire size, speed rating, load rating, and service description are appropriate for the truck's use.
• After installation, check for rubbing at full steering lock and through available suspension travel.

Do not use wheel spacers, adapters, or oversized tires to solve a fitment problem without confirming their legal, load, clearance, and installation requirements with the manufacturer and a qualified technician.

Plus Sizing And Common Upgrades

The supplied data does not identify the factory rim diameter, rim width, offset, backspacing, or tire size for this 2020 Ford F-350. Because the original baseline is unknown, a specific plus-size wheel or tire recommendation cannot be confirmed here.

When considering a larger rim diameter, compare the complete tire diameter, section width, wheel offset, and load capacity rather than looking at rim diameter alone. A larger wheel commonly requires a lower-profile tire to maintain a similar outside diameter, but the correct size must be checked against the truck's OEM specifications and available clearance.

Changing offset or backspacing can move the wheel closer to suspension components or farther toward the fender. Larger section widths can also increase rubbing risk. Recheck clearance after installation and do not reduce the required load capacity for appearance or handling preferences.

Installation Tips

Work on a level surface and support the vehicle with properly rated jack stands. Never rely on a jack alone while removing or installing wheels. Keep the wheel mounting surfaces clean and dry, and inspect the hub, studs, lug nuts, and wheel seat for damage or contamination.

Install each wheel using the correct lug nuts for the wheel. Tighten the lugs in a star or crisscross sequence, then apply the vehicle or wheel manufacturer's specified torque with a calibrated torque wrench. Do not use an impact tool as the final torque method unless the manufacturer specifically permits that procedure.

After driving a short distance, stop in a safe location and inspect for looseness, vibration, contact marks, or unusual noise. Recheck lug torque according to the wheel manufacturer's instructions. If the truck pulls, vibrates, rubs, or shows any interference, stop driving and correct the issue before further use.

Tools And Helpful Supplies

A calibrated torque wrench is important for final lug installation. A tread depth gauge, tire pressure gauge, jack stands, and a light can also help with inspection and installation. Select tools with ratings appropriate for a heavy-duty truck.

• Automotive torque wrench for final lug tightening.
• Heavy-duty tire pressure gauge for checking inflation after installation.

Always follow the torque, inflation, lifting, and wheel installation instructions supplied by Ford, the wheel manufacturer, and the tire manufacturer.

FAQs

What is the bolt pattern for the 2020 Ford F-350?

The supplied OEM fitment information lists an 8x170 bolt pattern. Confirm the specification for your exact truck before purchasing replacement wheels.

What is the center bore of the 2020 Ford F-350?

The supplied center bore is 124.9 mm. The replacement wheel's center bore must be compatible with the truck hub, and a smaller bore will not fit.

What lug thread size is listed for the 2020 Ford F-350?

The supplied thread size is M14 x 1.5. The wheel's lug seat and the lug nut design must also match. Thread size alone does not confirm lug nut compatibility.

What factory rim size does the 2020 Ford F-350 use?

The rim diameter and rim width are unknown in the supplied data and may vary by configuration. Check the door-jamb label, owner's manual, original wheel markings, or Ford service information. You can enter the confirmed dimensions in the calculator's custom wheel fields.

Can any 8x170 wheel fit a 2020 Ford F-350?

No. Matching the bolt pattern is only one part of fitment. Center bore, offset, backspacing, brake clearance, wheel load capacity, lug seat, and tire clearance must also be confirmed.

How do I compare a donor wheel with my truck?

Enter the donor vehicle under “Wheels from” and the 2020 Ford F-350 under “Installed on.” If the donor wheel is not listed, enter its diameter, width, and offset as a custom wheel, then compare the resulting dimensions and clearances.

Can I install larger wheels or tires?

A larger wheel or tire may be possible, but no specific upgrade can be confirmed without the original wheel and tire dimensions, exact truck configuration, load requirements, and physical clearance checks. Use the calculator for dimensional comparison and verify the final setup with OEM and manufacturer data.