2008 Honda Fit Wheel Interchange

2008 Honda Fit Wheel Fitment Guide

Known OEM Fitment For 2008 Honda Fit

The following specifications are the known OEM fitment values provided for the 2008 Honda Fit. Equipment can vary by trim, market, or replacement wheel, so confirm the information on the vehicle, in the owner’s manual, or through a Honda parts source before purchasing.

These values describe the listed OEM configuration and do not by themselves confirm that every 4x100 wheel will fit. Wheel design, brake clearance, center-bore fit, offset, load rating, lug-seat design, and tire clearance must also be checked.

How To Use The Wheel Interchange Calculator

Use the calculator to compare a donor vehicle’s wheels with the wheels installed on your 2008 Honda Fit. Enter the donor vehicle in the “Wheels from” fields and select the Honda Fit as the vehicle in the “Installed on” fields.

Review the bolt pattern, center bore, rim width, rim diameter, and offset comparison. A matching bolt pattern is necessary, but it is not enough to establish safe fitment. The calculator is a comparison aid and does not replace a physical test fit or confirmation from OEM documentation.

You can also select “Custom wheel size” to enter a proposed rim diameter, rim width, and offset. Use “Custom tire size” to enter the tire section width and aspect ratio. When rim diameter changes, the calculator updates the tire diameter in the comparison, helping you evaluate overall diameter changes before buying.

Check the complete wheel and tire assembly for brake, suspension, fender, and inner-sidewall clearance. If the calculator identifies an unknown or conflicting value, confirm it from the wheel manufacturer, tire manufacturer, vehicle identification label, owner’s manual, or a Honda parts source.

Fitment Checklist Before You Buy

Confirm that the wheel uses the 4x100 bolt pattern and has a center bore of 56.1 mm or larger. A larger center bore may require correctly sized hub-centric rings; a smaller center bore will not fit over the vehicle hub without approved machining by a qualified wheel specialist.

Compare the proposed wheel’s diameter, width, and offset with the known 14 x 5.5-inch, ET45 configuration. Changes in offset or width can move the wheel toward suspension components or the fender. Do not assume that a wheel clears the brakes simply because its bolt pattern matches.

Verify that the replacement tire has an appropriate load rating, speed rating, approved rim-width range, and overall diameter for the vehicle. Maintain adequate clearance at full steering lock and through suspension travel. Check clearance with the vehicle loaded as recommended by the manufacturer.

Confirm the lug hardware. The listed thread size is M12 x 1.5, but the correct lug nut seat style and usable thread engagement must match the wheel. Never force incompatible lug nuts onto a wheel.

Plus Sizing And Common Upgrades

Plus sizing changes the wheel diameter while maintaining a similar overall tire diameter by using a lower-profile tire. The correct replacement size is not known from the supplied information alone and should not be guessed. Use the calculator to compare a proposed custom wheel and tire combination against the listed 175/65R14 configuration.

When changing wheel diameter or width, check calculated overall diameter, sidewall height, speedometer effect, load capacity, brake clearance, suspension clearance, and fender clearance. A wider tire can contact the inner wheel well or bodywork even when its overall diameter appears close to stock.

Do not use spacers, adapters, or aggressive offset changes as a substitute for confirming proper wheel fitment. Any such component must be specifically rated for the application and installed according to its manufacturer’s instructions.

Installation Tips

Before installation, clean the hub and wheel mounting surfaces. The mating faces should be flat, dry, and free of rust, paint buildup, grease, and debris. Do not lubricate the wheel stud or lug nut threads unless the vehicle or hardware manufacturer specifically instructs you to do so.

Install each wheel by hand and start every lug nut by hand to avoid cross-threading. Tighten the lug nuts in a crisscross pattern, then lower the vehicle enough to prevent rotation and torque them to the vehicle or wheel manufacturer’s specified value. The correct torque value is not provided here, so confirm it in the owner’s manual or an OEM service source.

After installation, rotate the steering from lock to lock and inspect for contact. Check clearance again after a short drive and recheck lug torque according to the wheel manufacturer’s instructions. Stop driving if you notice vibration, rubbing, loose hardware, or steering changes.

Tools And Helpful Supplies

Useful equipment includes a properly sized socket, a breaker bar, a vehicle jack, jack stands rated for the vehicle, wheel chocks, a tire-pressure gauge, and a calibrated torque wrench. A torque wrench can help prevent both loose wheel hardware and damage from excessive tightening.

Shop automotive torque wrenches on Amazon

For aftermarket wheels with a larger center bore, use hub-centric rings only when the ring dimensions and material are appropriate for the wheel and vehicle. Confirm the required dimensions before ordering. A thread chaser or suitable cleaning brush may also help clean mounting hardware, but it must not be used to alter the wheel or hub.

FAQs

What is the bolt pattern for the 2008 Honda Fit?

The known bolt pattern is 4x100, meaning four studs on a 100 mm pitch-circle diameter. Bolt pattern alone does not confirm complete wheel compatibility.

What is the center bore?

The known center bore is 56.1 mm. A replacement wheel with a smaller bore will not fit over the hub. A larger bore may require correctly sized hub-centric rings.

What lug thread size is listed for this vehicle?

The listed thread size is M12 x 1.5. Confirm the lug nut seat style and required hardware for the specific wheel, because thread size does not identify the complete lug nut specification.

What is the listed OEM wheel size?

The known configuration is a 14 x 5.5-inch wheel with ET45 offset and 4.52-inch backspacing. Confirm the vehicle’s actual equipment because trim and market differences may apply.

Can any 4x100 wheel fit the 2008 Honda Fit?

No. The wheel must also clear the brakes and suspension, use a suitable center bore, have an appropriate offset and width, accept compatible lug hardware, and meet load requirements. Use the calculator for comparison, then verify the assembly physically and with OEM or manufacturer information.

Can I install larger wheels?

Larger wheels may be possible, but the correct size cannot be confirmed from the supplied data alone. Enter the proposed custom wheel and tire dimensions in the calculator and compare overall diameter, width, offset, and clearance. Tire load and speed ratings must also be suitable.

Does changing rim diameter change the tire comparison?

Yes. In this calculator, changing the custom rim diameter updates the tire diameter in the comparison. Recheck the complete wheel and tire combination rather than evaluating rim diameter by itself.

Where can I confirm the final fitment?

Check the tire-and-loading label, owner’s manual, Honda service information, the wheel manufacturer’s fitment data, and the tire manufacturer’s approved rim-width range. A qualified tire or wheel technician can also perform a clearance inspection before road use.