2017 Honda Fit Wheel Interchange

2017 Honda Fit Wheel Fitment Guide

Known OEM Fitment For 2017 Honda Fit

The following specifications are the known reference values for the 2017 Honda Fit on this page. Fitment can vary by trim, market, wheel design, and replacement parts, so confirm the specifications on your vehicle before ordering.

These values identify the basic wheel and tire reference, but they do not confirm every clearance requirement. Tire load index, speed rating, brake clearance, suspension clearance, and fender clearance should be verified separately. Use the tire information label on the driver-side door jamb, the owner's manual, and the wheel markings as OEM sources for your specific vehicle.

How To Use The Wheel Interchange Calculator

Use the calculator to compare a donor vehicle's wheel and tire measurements with the specifications for your 2017 Honda Fit. Select the donor vehicle under “Wheels from” and select the Honda Fit under “Installed on.” Review the diameter, width, offset, bolt pattern, center bore, and tire-size comparison before treating a wheel as a possible candidate.

You can also enter a custom wheel size by changing rim diameter, rim width, and offset. Enter a custom tire section width and aspect ratio when evaluating a different tire size. When rim diameter changes, the calculator updates the tire diameter comparison, which helps show whether the proposed tire is close to the reference rolling diameter.

A calculator result is a screening tool, not a guarantee of safe installation. A wheel can match the bolt pattern and still contact the brake caliper, strut, suspension, or fender. Confirm physical clearances and use the correct lug hardware before driving.

Fitment Checklist Before You Buy

Start with the complete wheel specification, not just the bolt pattern. The known reference for this page is 4x100 with a 56.1 mm center bore, M12 x 1.5 threads, a 15 x 6.0 inch wheel, ET50 offset, and a 185/60R15 tire. Compare every relevant measurement with the calculator and the wheel manufacturer's published data.

• Confirm the wheel has a 4x100 bolt pattern and is designed for the vehicle's M12 x 1.5 lug hardware.
• Check the center bore. A smaller bore will not fit over the hub. A larger bore may require correctly sized hub-centric rings if the wheel manufacturer permits their use.
• Compare offset and backspacing to the original wheel. These measurements affect inner suspension clearance and outer fender position.
• Verify brake-caliper clearance using the wheel maker's application data or a physical test fit.
• Confirm the replacement tire's load index and speed rating meet or exceed the vehicle requirements shown on the door label or in the owner's manual.
• Inspect used wheels for bends, cracks, corrosion around the bead seat, damaged lug holes, and missing or altered hardware.
• Check that the wheel's seat type matches the lug nuts. Do not assume conical, ball-seat, and other lug designs are interchangeable.

Plus Sizing And Common Upgrades

Plus sizing usually increases wheel diameter while reducing tire sidewall height so the overall tire diameter remains near the original reference. The known reference here is 185/60R15, but no specific alternative size is confirmed by the information provided. Do not treat an automatically calculated diameter match as proof that a tire will clear the vehicle.

For any proposed upgrade, compare the tire's calculated diameter, section width, and sidewall height with the original. Also check the replacement wheel's width and offset. A wider tire or a lower offset can move the tire closer to the strut or fender, while a higher offset can reduce inner clearance. Confirm the final assembly at full steering lock and through the suspension's usable travel.

Changes in wheel and tire size can affect speedometer accuracy, ride comfort, steering effort, road noise, wet-weather behavior, and wheel damage risk. Use only a tire size and wheel combination approved by the tire and wheel manufacturers for your vehicle.

Installation Tips

Test-fit one wheel on the front and rear positions before mounting all four tires. Remove dirt, rust, and paint buildup from the hub and wheel mounting faces so the wheel sits flat. Never use extra washers or improperly sized spacers to compensate for an incompatible wheel.

Install the correct lug nuts by hand first to prevent cross-threading. Tighten them in a star pattern and use the vehicle manufacturer's specified torque. The exact torque value was not provided here, so confirm it in the owner's manual or an official Honda service source rather than guessing.

After installation, rotate the steering from lock to lock and inspect for contact. Check clearance around the brake caliper, strut, spring, tie-rod area, and inner fender. Recheck lug torque after the first short drive and again according to the wheel or vehicle manufacturer's instructions. Stop driving if you notice rubbing, vibration, looseness, or air loss.

Tools And Helpful Supplies

A torque wrench, correctly sized socket, jack, jack stands, wheel chocks, and a tire-pressure gauge are useful for a careful wheel change. Use jack stands on a solid, level surface and follow the vehicle's approved lifting points. A product search for a torque wrench can help you find suitable options, but verify its measurement range and accuracy before use.

A hub and wheel mounting surface should be clean and dry. A wheel chock set can help prevent vehicle movement during service. Never work under a vehicle supported only by a jack.

FAQs

What is the bolt pattern for the 2017 Honda Fit?

The known reference bolt pattern is 4x100, meaning four wheel studs or holes on a 100 mm pitch circle diameter.

What center bore is listed for the 2017 Honda Fit?

The known center bore is 56.1 mm. A replacement wheel with a smaller center bore will not fit over the hub. A larger bore may need properly sized hub-centric rings, subject to the wheel manufacturer's instructions.

What wheel size is listed as the OEM reference?

The known reference is a 15 x 6.0 inch wheel with ET50 offset and 4.97 inches of backspacing. Confirm your specific trim and market using the original wheel markings, door label, owner's manual, or an official Honda source.

What tire size is used as the reference?

The known reference tire size is 185/60R15. The required load index and speed rating were not provided, so confirm both on the vehicle's tire placard and with the tire manufacturer.

Can any 4x100 wheel fit the 2017 Honda Fit?

No. Matching 4x100 only confirms the basic bolt pattern. Center bore, offset, backspacing, brake clearance, wheel width, lug-seat design, load rating, and fender or suspension clearance must also be checked.

How do I compare a donor wheel with my Honda Fit?

Use the on-page calculator to compare “Wheels from” the donor vehicle with “Installed on” your 2017 Honda Fit. Review all wheel measurements and the tire diameter comparison, then physically verify clearance before purchase or installation.

Does changing rim diameter change the tire comparison?

Yes. The calculator updates the tire diameter comparison when you change rim diameter. A diameter comparison still does not confirm brake, suspension, or fender clearance.

What lug thread size is listed?

The known thread size is M12 x 1.5. The lug nut seat type and final tightening torque were not provided, so match the lug hardware to the wheel and confirm torque through an OEM or wheel manufacturer source.